Mitsubishi Montero (2002-2004). Manual — part 938
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-235
STEP 4. Check A/T control solenoid valve assembly
connector C-03 and PCM connector D-136 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Are the connectors and terminals in good condition?
YES : Replace the torque converter clutch solenoid valve.
Refer to GROUP 23B, Valve Body
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
AC204395
CONNECTOR : C-03
AE
C-03 (B)
6
10
4
9
5
3
8
2
7
1
AC204681AD
CONNECTOR: D-136
D-136 (GR)
121 122
123
124
125 126 127 128 129 130
131 132
133
134 135
136 137 138
139 140
141
142 143
144
145
146
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-236
STEP 5. Using scan tool MB991502, check data list item 52:
Amount of Torque Converter Clutch Slippage. (Second
check)
(1) Connect scan tool MB991502 to the data link connector.
(2) Start the engine and run at constant speed of 60 km/h (37
mph). (Gear range: 3rd gear)
(3) Set scan tool MB991502 to data reading mode for item 52,
Amount of Torque Converter Clutch Slippage.
• Driving at constant speed of 60 km/h (31 mph), the dis-
play should be "
−10 to 10 r/min."
• If the accelerator pedal is released, the display on the
scan tool changes. (50 km/h (31 mph) and less).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the torque converter clutch slippage within the
specified range?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
− How to Cope with
Intermittent Malfunction
NO : Go to Step 6.
STEP 6. Replace the PCM.
(1) Replace the PCM.
(2) Test drive the vehicle.
(3) Check for A/T diagnostic trouble code.
Q: Is DTC 53 set?
YES : Go to Step 7.
NO : The procedure is complete.
STEP 7. Replace the valve body.
(1) Replace the valve body. Refer to GROUP 23B,
Transmission
.
(2) Test drive the vehicle.
(3) Check for A/T diagnostic trouble code.
Q: Is DTC 53 set?
YES : Replace the Torque Converter. Refer to
Transmission and Transfer Assembly.
NO : The procedure is complete.
ACX01539AD
MB991502
16-PIN
ACX02161AD
VALVE BODY ASSEMBLY
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-237
DTC 54: A/T Control Relay System
AC205196AB
AC204167
CONNECTOR : A-03
AT
A-03 (B)
6
12
5
3 4
2
1
9 10
8
7
11
AC204750
CONNECTOR : D-13
AB
PCM
1
3 4
2
DIAGNOSTIC TROUBLE CODE PROCEDURES <AUTOMATIC TRANSMISSION>
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
23Ac-238
.
CIRCUIT OPERATION
• A/T control relay (terminal 1) receives battery
positive voltage through a battery.
• The PCM (terminal 127) applies voltage to ener-
gize the A/T control relay (terminal 4). With the A/
T control relay energized, system voltage is
applied to the PCM (terminals 123 and 124).
.
DTC SET CONDITIONS
If the A/T control relay voltage is less than 7 volts at
the PCM (terminals 123 and 124) when the ignition
switch is in the "ON" position, DTC 54 is set. The
transmission is locked into the 3rd gear as a fail-safe
measure, and the "N" range light flashes once per
second.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• Malfunction of the A/T control relay
• Damaged harness, connector
• Malfunction of the PCM
AC204171
CONNECTOR : D-14
AM
4
9
8
6
5
7
1 2
3
10
AC204681AD
CONNECTOR: D-136
D-136 (GR)
121 122
123
124
125 126 127 128 129 130
131 132
133
134 135
136 137 138
139 140
141
142 143
144
145
146
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст