Mitsubishi Montero (2002-2004). Manual — part 322
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-335
STEP 23. Check the ground circuit to the taillight (LH). Test
at rear light (LH) connector G-16.
(1) Disconnect rear light (LH) connector G-16 and measure the
resistance available at the wiring harness side of the
connector.
(2) Measure the resistance value between terminal 3 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : No action is necessary and testing is complete.
NO : Go to Step 24.
STEP 24. Check rear light (LH) connector G-16 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is rear light (LH) connector G-16 in good condition?
YES : Go to Step 25.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the taillights illuminate normally.
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
4
1
2
3
AC100265AB
CONNECTOR G-16
(HARNESS SIDE)
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-336
STEP 25. Check the wiring harness between rear light (LH)
connector G-16 (terminal 3) and ground.
NOTE: Also check intermediate connector F-10 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector F-10 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between rear light (LH) connector
G-16 (terminal 3) and ground in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the taillights illuminate normally.
STEP 26. Check the taillight bulb (LH).
(1) Remove the taillight bulb (LH).
(2) Verify that the taillight bulb (LH) is not damaged or burned
out.
Q: Is the taillight bulb (LH) in good condition?
YES : Go to Step 27.
NO : Replace the taillight bulb (LH). Verify that the taillights
(LH) illuminates normally.
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
AC204178
CONNECTOR : F-10
AD
F-10(GR)
F-10(GR)
3
1
2
4
5
6
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-337
STEP 27. Check the ground circuit to the taillight (LH). Test
at rear light (LH) connector G-16.
(1) Disconnect rear light (LH) connector G-16 and measure the
resistance available at the wiring harness side of the
connector.
(2) Measure the resistance value between terminal 3 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 30.
NO : Go to Step 28.
STEP 28. Check rear light (LH) connector G-16 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is rear light (LH) connector G-16 in good condition?
YES : Go to Step 29.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the taillights (LH) illuminates
normally.
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
4
1
2
3
AC100265AB
CONNECTOR G-16
(HARNESS SIDE)
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-338
STEP 29. Check the wiring harness between rear light (LH)
connector G-16 (terminal 3) and ground.
NOTE: Also check intermediate connector F-10 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector F-10 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between rear light (LH) connector
G-16 (terminal 3) and ground in good condition?
YES : Replace the rear combination light socket (LH). Verify
that the taillight (LH) illuminates normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the taillights (LH) illuminates normally.
AC204179
CONNECTOR : G-16
AH
HARNESS SIDE
G-16(B)
G-16(B)
3
4
2
1
AC204178
CONNECTOR : F-10
AD
F-10(GR)
F-10(GR)
3
1
2
4
5
6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст