Mitsubishi Montero (2002-2004). Manual — part 297
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-235
STEP 3. Check the windshield wiper motor.
(1) Disconnect windshield wiper motor connector B-12.
(2) Connect a battery to the windshield wiper motor as shown.
Then check the windshield wiper motor operates normally
at high and low speeds.
Q: Does the windshield wiper motor operate normally?
YES : Go to Step 4.
NO : Replace the windshield wiper motor. Verify that the
windshield wiper works normally.
STEP 4. Check the ground circuit to the windshield wiper
motor. Test at windshield wiper motor connector B-12.
(1) Disconnect windshield wiper motor connector B-12 and
measure the resistance available at the wiring harness side
of the connector.
(2) Measure the resistance value between terminal 5 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 7.
NO : Go to Step 5.
1
2 3
4
5
1
2 3
4
5
ACX02403
B-12
AB
LOW-SPEED
HIGH-SPEED
AC205116 AC
CONNECTOR: B-12
B-12 (B)
B-12 (B)
1
2
3
4
5
ACX01576AB
CONNECTOR B-12
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-236
STEP 5. Check windshield wiper motor connector B-12 for
loose, corroded or damaged terminals, or terminals
pushed back in the connector.
Q: Is windshield wiper motor connector B-12 in good
condition?
YES : Go to Step 6.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the windshield wiper works
normally.
STEP 6. Check the wiring harness between windshield
wiper motor connector B-12 (terminal 5) and ground.
Q: Is the wiring harness between windshield wiper motor
connector B-12 (terminal 5) and ground in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the connector
may have loose, corroded or damaged terminals, or
terminals pushed back in the connector. Repair the
wiring harness as necessary. Verify that the
windshield wiper works normally.
STEP 7. Check the ignition switch (ACC) circuit to the
front-ECU. Test at front-ECU connector A-08X.
(1) Disconnect front-ECU connector A-08X, and measure at
the relay box side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 24 and ground.
• The voltage should be approximately 12 volts (battery
positive voltage).
Q: Is the measured voltage approximately 12 volts (battery
positive voltage)?
YES : Go to Step 10.
NO : Go to Step 8.
AC205116 AC
CONNECTOR: B-12
B-12 (B)
B-12 (B)
AC205116 AD
CONNECTOR: B-12
B-12 (B)
(HARNESS SIDE)
B-12 (B)
1
2
3
4
5
AC205138
CONNECTOR: A-08X
AC
BATTERY
FRONT-ECU
A-08X
A-08X
21
22
23
24
25
27 26
28
29
30
31
ACX01611AB
CONNECTOR A-08X
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-237
STEP 8. Check front-ECU connector A-08X for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is front-ECU connector A-08X in good condition?
YES : Go to Step 9.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the windshield wiper works
normally.
STEP 9. Check the wiring harness between front-ECU
connector A-08X (terminal 24) and the ignition switch
(ACC).
NOTE: Also check intermediate connector D-28, junction block
connectors D-208 and D-221 for loose, corroded, or damaged
terminals, or terminals pushed back in the connector. If inter-
mediate connector D-28, junction block connector D-208 or D-
221 is damaged, repair or replace the damaged component(s)
as described in GROUP 00E, Harness Connector Inspection
.
Q: Is the wiring harness between front-ECU connector A-
08X (terminal 24) and the ignition switch (ACC) in good
condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the connector
may have loose, corroded or damaged terminals, or
terminals pushed back in the connector. Repair the
wiring harness as necessary. Verify that the
windshield wiper works normally.
AC205138
CONNECTOR: A-08X
AC
BATTERY
FRONT-ECU
A-08X
A-08X
AC205138
CONNECTOR: A-08X
AC
BATTERY
FRONT-ECU
A-08X
A-08X
AC204170
CONNECTOR : D-28
AI
2 3
27
32
28
33
16
15
4 5
19
18
29
17
34
7 8
35
22
21
9 10
30
36
31
37
25
24
23
6
20
1
14
26
11
13
12
38
ACX02285
CONNECTORS: D-208, D-221
BW
JUNCTION BLOCK (FRONT VIEW)
D-208
D-221
D-208
D-221
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-238
STEP 10. Check front-ECU connector A-08X for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is front-ECU connector A-08X in good condition?
YES : Go to Step 11.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the windshield wiper works
normally.
AC205138
CONNECTOR: A-08X
AC
BATTERY
FRONT-ECU
A-08X
A-08X
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст