Mitsubishi Montero (2002-2004). Manual — part 296
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-231
INSPECTION PROCEDURE G-1: Windshield Wiper and Washer: The windshield wiper does not work
at all.
NOTE: This troubleshooting procedure requires the
use of scan tool MB991502 and SWS monitor kit
MB991862. For details on how to use the SWS mon-
itor, refer to "How to use SWS monitor
Windshield Wiper Motor Circuit
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-232
.
CIRCUIT OPERATION
• The windshield wiper and washer switch sends a
signal through the column-ECU (incorporated in
the column switch) to the front-ECU. If the col-
umn-ECU sends a windshield wiper and washer
switch "ON" signal to the front-ECU, the front-
ECU turns on the relay (incorporated in the front-
ECU), thus causing the windshield wiper and
washer motor to be turned on.
• If the SWS communication line is defective, the
front-ECU operates windshield wiper motor by
using the other communication lines (wiper
backup circuit) instead of that line. In this case,
the windshield wiper works at low speed regard-
less of the windshield wiper and washer switch
positions ("LO" or "HIGH").
.
TECHNICAL DESCRIPTION (COMMENT)
If the windshield wiper does not work at all, the wind-
shield wiper motor, column switch (windshield wiper
and washer switch) or the front-ECU may be defec-
tive.
.
TROUBLESHOOTING HINTS
• The windshield wiper motor may be defective
• The column switch (windshield wiper and washer
switch) may be defective
• The front-ECU may be defective
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
AC205142AB
CONNECTOR: A-05
A-05(B)
AC205138
CONNECTOR: A-08X
AB
BATTERY
FRONT-ECU
A-08X
AC205116 AB
CONNECTOR: B-12
B-12 (B)
AC204170
CONNECTOR : D-28
BB
ACX02285
CONNECTORS: D-208, D-221
AI
D-208
JUNCTION BLOCK (FRONT VIEW)
D-221
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-233
DIAGNOSIS
Required Special Tools:
• MB991223: Harness Set
• MB991502: Scan Tool (MUT-II)
• MB991862: SWS Monitor Kit
STEP 1. Use scan tool MB991502 to select "ECU COMM
CHK" on the SWS monitor display.
Check the following ECUs:
• Column-ECU
• Front-ECU
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "lock" (OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector
(16-pin).
(2) Connect SWS monitor kit MB991862 to the data link
connector (13-pin).
(3) Turn the ignition switch to the "ON" position.
(4) Operate scan tool MB991502 according to the procedure
below to display "ECU COMM CHECK."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "ECU COMM CHK".
(5) Scan tool MB991502 should show "OK" on the "ECU
COMM CHK" menus for both the "COLUMN ECU" and the
"FRONT ECU" menus.
Q: Is "OK" displayed on the "COLUMN ECU" and "FRONT
ECU" menu?
"OK" is displayed for all the items : Go to Step 2.
"NG" is displayed on the "COLUMN ECU" menu : Refer
to Inspection Procedure A-2 "Communication with
column switch (column-ECU) is not possible
"NG" is displayed on the "FRONT ECU" menu : Refer to
Inspection procedure A-4 "Communication with front-
ECU is not possible
AC204222AB
16-pin
13-pin
MB991502
MB991862
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-234
STEP 2. Check the input signal by using "FUNCTION
DIAG." menu of the SWS monitor.
Check the input signals from the following switches:
• Ignition switch: ACC
• Windshield wiper switch: INT
Operate the scan tool according to the procedure below to dis-
play "F.WIPER INT."
1. Select "SYSTEM SELECT."
2. Select "SWS."
3. Select "SWS MONITOR."
4. Select "FUNCTION DIAG."
5. Select "WIPER."
6. Select "F.WIPER INT."
Check that normal conditions are displayed on the items
described in the table below.
Q: Are normal conditions displayed for "INT WIPER SW"
and "FRONT ECU ACK"?
YES : Go to Step 3.
NO :
• Normal condition is not displayed on the "INT
WIPER SW." Replace the column switch. Verify
that the windshield wiper works normally.
• Normal condition is not displayed on the "FRONT
ECU SW." Replace the front-ECU. Verify that the
windshield wiper works normally.
ITEM NO.
ITEM NAME
NORMAL
CONDITION
ITEM 05
INT WIPER SW
ON
ITEM 70
FRONT ECU
ACK
NORMAL ACK or
HI-BEAM ACK
AC204222AB
16-pin
13-pin
MB991502
MB991862
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст