Mitsubishi Montero (2002-2004). Manual — part 660
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-337
STEP 11. Using scan tool MB991502, check data list item
14: Throttle Position Sensor (sub).
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Detach the intake air hose at the throttle body.
(4) Disconnect the connector of the throttle position sensor.
(5) Use test harness special tool (MB991348) to connect only
terminals No. 1, No. 2, No. 3, and No. 4.
(6) Set scan tool MB991502 to the data reading mode for item
14, Throttle Position Sensor (sub).
• Output voltage should be between 2.2 and 2.8 volts
when the throttle valve is fully closed with your finger.
• Output voltage should be between 3.8 and 4.9 volts
when the throttle valve is fully open with your finger.
(7) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
NO : Replace the PCM. Then go to Step 12.
STEP 12. Using scan tool MB991502, read the diagnostic
trouble code (DTC).
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) After the DTC has been deleted, read the DTC again.
(4) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is DTC P0222 set?
YES : Retry the troubleshooting.
NO : The inspection is complete.
ACX01539
16-PIN
MB991502
AC
ACX01539
16-PIN
MB991502
AC
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-338
P0223 Throttle Position Sensor (Sub) Circuit High Input
.
CIRCUIT OPERATION
• A 5-volt power supply is applied on the TPS (sub)
power terminal (terminal No. 2) from the PCM
(terminal No. 106).
The ground terminal (terminal No. 4) is grounded
with PCM (terminal No. 105).
• When the throttle valve shaft is turned from the
idle position to the fully opened position, the
resister between the TPS (sub) output terminal
(terminal No. 3) and ground terminal will increase
according to the rotation.
.
AK201162
RED
GREEN
BLA
CK
B-05
5 V
106
2
THROTTLE
POSITION
SENSOR
(SUB)
POWERTRAIN CONTROL MODULE (PCM)
113
105
3
4
Throttle Position Sensor (Sub) Circuit
6
1 2 3 4 5
9192
939495
96979899
100
105
113114
115116117
118119120
106
107108109
110111112
101102103
104
D-135
(MU803805)
AK201173
THROTTLE
POSITION
SENSOR
AB
B-05(B)
CONNECTOR: B-05
AK201038AF
CONNECTOR: D-135
PCM
D-135(GR)
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-339
TECHNICAL DESCRIPTION
• The TPS (sub) outputs voltage which corre-
sponds to the throttle valve opening angle.
• The PCM checks whether the voltage is within a
specified range.
.
DTC SET CONDITIONS
Check Conditions
• Ignition switch "ON" position.
Judgement Criteria
• TPS (sub) output voltage should be 4.8 volts or
more for 0.5 seconds.
.
TROUBLESHOOTING HINTS (The most likely
causes for this code to be set are:)
• TPS failed or maladjusted.
• Open or shorted TPS (sub) circuit, or loose con-
nector.
• PCM failed.
DIAGNOSIS
Required Special Tool:
• MB991502: Scan Tool (MUT-II)
STEP 1. Using scan tool MB991502, check data list item 14:
Throttle Position Sensor (sub).
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to the "LOCK"(OFF) position before con-
necting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Detach the intake air hose at the throttle body.
(4) Disconnect the connector of the throttle position sensor.
(5) Use test harness special tool (MB991348) to connect only
terminals No. 1, No. 2, No. 3, and No. 4.
(6) Set scan tool MB991502 to the data reading mode for item
14, Throttle Position Sensor (sub).
• Output voltage should be between 2.2 and 2.8 volts
when the throttle valve is fully closed with your finger.
• Output voltage should be between 3.8 and 4.9 volts
when the throttle valve is fully open with your finger.
(7) Turn the ignition switch to the "LOCK"(OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use Troubleshooting/
Inspection Service Points
NO : Go to Step 2.
STEP 2. Check connector B-05 at throttle position sensor
for damage.
Q: Is the connector in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 9.
ACX01539
16-PIN
MB991502
AC
AK201174
1
6 5 4 3 2
B-05(B)
CONNECTOR: B-05
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
TSB Revision
DIAGNOSTIC TROUBLE CODE PROCEDURES
13Ac-340
STEP 3. Check the continuity at throttle position sensor
harness side connector B-05.
(1) Disconnect the connector B-05 and measure at the harness
side.
(2) Measure the continuity between terminal No. 4 and ground
• Should be less than 2 ohms.
Q: Is the continuity normal?
YES : Go to Step 7.
NO : Go to Step 4.
STEP 4. Check connector D-135 at PCM for damage.
Q: Is the connector in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 9.
AK201174
1
6 5 4 3 2
B-05(B)
CONNECTOR: B-05
HARNESS
CONNECTOR:
COMPONENT SIDE
AB
AK201446
1
6 5 4 3 2
AB
B-05 HARNESS
CONNECTOR:
COMPONENT SIDE
AK200947
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
CONNECTOR: D-135
HARNESS CONNECTOR:
COMPONENT SIDE
AB
PCM
D-135(GR)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст