Mitsubishi Montero (2002-2004). Manual — part 348
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-439
STEP 7. Check the wiring harness between joint connector
(2) A-15 (terminal 3) and fog light (LH) connector A-21
(terminal 1).
NOTE: Also check intermediate connector A-25 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector A-25 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between joint connector (2) A-15
(terminal 3) and fog light (LH) connector A-21 (terminal
1) in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the fog lights illuminate normally.
STEP 8. Check the fog light bulb (RH).
(1) Remove the fog light bulb (RH).
(2) Verify that the fog light bulb (RH) is not damaged or burned
out.
Q: Is the fog light bulb (RH) in good condition?
YES : Go to Step 9.
NO : Replace the fog light bulb (RH). Verify that the fog
lights illuminate normally.
AC204185
CONNECTORS : A-15, A-21, A-25
A-21(B)
A-15
AC
A-15
A-25
HARNESS SIDE
A-21(B)
A-25(B)
14
13
4
1112
5
3
10
8 9
2
7
1
6
1
2
4
2
3
1
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-440
STEP 9. Check the ground circuit to the fog light (RH). Test
at fog light (RH) connector A-31.
(1) Disconnect fog light (RH) connector A-31 and measure the
resistance available at the wiring harness side of the
connector.
(2) Measure the resistance value between terminal 2 and
ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 12.
NO : Go to Step 10.
STEP 10. Check fog light (RH) connector A-31 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is fog light (RH) connector A-31 in good condition?
YES : Go to Step 11.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the fog lights illuminate normally.
AC204166
CONNECTOR : A-31
HARNESS
SIDE
A-31(B)
A-31(B)
AD
1
2
AC100270
1
2
AC
CONNECTOR A-31
(HARNESS SIDE)
AC204166
CONNECTOR : A-31
HARNESS
SIDE
A-31(B)
A-31(B)
AD
1
2
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-441
STEP 11. Check the wiring harness between fog light (RH)
connector A-31 (terminal 2) and ground.
NOTE: Also check intermediate connector A-25 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector A-25 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between fog light (RH) connector
A-31 (terminal 2) and ground in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the fog lights illuminate normally.
STEP 12. Check joint connector (2) A-15 and fog light (RH)
connector A-31 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
Q: Are joint connector (2) A-15 and fog light (RH)
connector A-31 in good condition?
YES : Go to Step 13.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the fog lights illuminate normally.
AC204166
CONNECTOR : A-31
HARNESS
SIDE
A-31(B)
A-31(B)
AD
1
2
AC204167
CONNECTOR : A-25
A-25(B)
A-25(B)
AK
4
2
3
1
AC204167
CONNECTOR : A-15
AD
14
13
4
1112
5
3
10
8 9
2
7
1
6
AC204166
CONNECTOR : A-31
HARNESS
SIDE
A-31(B)
A-31(B)
AD
1
2
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-442
STEP 13. Check the wiring harness between joint
connector (2) A-15 (terminal 2) and fog light (RH)
connector A-31 (terminal 1).
NOTE: Also check intermediate connector A-25 for loose, cor-
roded, or damaged terminals, or terminals pushed back in the
connector. If intermediate connector A-25 is damaged, repair or
replace the damaged component(s) as described in GROUP
00E, Harness Connector Inspection
Q: Is the wiring harness between joint connector (2) A-15
(terminal 2) and fog light (RH) connector A-31 (terminal
1) in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the fog lights illuminate normally.
STEP 14. Check the fog light indicator light bulb.
(1) Remove the fog light indicator light bulb.
(2) Verify that the fog light indicator light bulb is not damaged or
burned out.
Q: Is the fog light indicator light bulb in good condition?
YES : Go to Step 15.
NO : Replace the fog light indicator light bulb. Verify that
the fog light indicator light illuminates normally.
AC204185
CONNECTORS : A-15, A-25
A-15
AL
A-15
A-25
A-25(B)
14
13
4
1112
5
3
10
8 9
2
7
1
6
4
2
3
1
AC204166
CONNECTOR : A-31
HARNESS
SIDE
A-31(B)
A-31(B)
AD
1
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст