Mitsubishi Montero (2002-2004). Manual — part 293
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-219
STEP 10. Check the sunroof switch.
Q: Does the check above meet the values in the table?
YES : Go to Step 11.
NO : Replace the sunroof switch. The sunroof function
should now work normally.
STEP 11. Check the ground circuit to the sunroof switch.
Test at sunroof switch connector F-01.
(1) Disconnect the sunroof switch connector F-01 and measure
at the harness side.
(2) Measure the resistance between terminal 4 and ground.
• The resistance should equal 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 14.
NO : Go to Step 12.
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
OFF
3
− 4, 4 − 5, 4 − 6 Open circuit
UP
3
− 4
Less than 2 ohms
OPEN
4
− 5
CLOSE/DOWN
4
− 6
AC203857
6
5
4
3
2
1
AB
OPEN
UP
CLOSE/
DOWN
AC203849AB
F-01
(HARNESS SIDE)
CONNECTOR: F-01
F-01 (B)
1
2
3
4
5
6
1
2
3
4
5
6
AC102943AD
CONNECTOR F-01
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-220
STEP 12. Check sunroof switch connector F-01 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is sunroof switch connector F-01 in good condition?
YES : Go to Step 13.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. The sunroof function should now work
normally.
STEP 13. Check the harness wire between sunroof switch
connector F-01 (terminal 4) and ground.
NOTE:
Also check intermediate connectors F-24 and D-26 for
loose, corroded or damaged terminals, or terminals pushed
back in the connectors. If intermediate connectors F-24 and D-
26 are damaged, repair or replace the damaged component(s)
as described in GROUP 00E, Harness Connector Inspection
.
Q: Is the harness wire between sunroof switch connector
F-01 (terminal 4) and ground in good condition?
YES : No action is necessary and testing is complete.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. The sunroof
function should now work normally.
AC203849 AC
F-01(B)
CONNECTOR: F-01
F-01(B)
6
5
4
3
2
1
AC203849AB
F-01
(HARNESS SIDE)
CONNECTOR: F-01
F-01 (B)
1
2
3
4
5
6
AC204484
AF
CONNECTOR: F-24
F-24
F-24
AC000758
CONNECTORS: D-01, D-26
AD
D-01
D-26
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-221
STEP 14. Check the sunroof switch connector F-01 and
sunroof motor assembly connector F-02 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is sunroof switch connector F-02 and sunroof motor
assembly connector F-01 in good condition?
YES : Replace the sunroof motor assembly. The sunroof
function should now work normally.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. The sunroof function should now work
normally.
AC203862AB
CONNECTORS: F-01, F-02
F-01 (B)
F-01 (B)
F-02
5
4
3
2
1
10
9
8
7
6
6
5
4
3
2
1
F-02
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-222
INSPECTION PROCEDURE F-2: Sunroof: Any of the sunroof switch positions is defective.
.
TECHNICAL DESCRIPTION (COMMENT)
The sunroof switch or the sunroof motor assembly
may be defective.
.
TROUBLESHOOTING HINTS
• The sunroof switch may be defective
• The sunroof motor assembly may be defective
• The wiring harness or connectors may have
loose, corroded or damaged terminals, or termi-
nals pushed back in the connector
Sunroof Switch Circuit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст