Mitsubishi Montero (2002-2004). Manual — part 235
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54Ba-17
• TURN SIGNAL
• BUZZER
NOTE: The headlight automatic shutdown function
works in approximately one second after the lighting
monitor tone alarm starts sounding, and then the
tone alarm ceases sounding.
ITEM
ITEM
NO.
INPUT SIGNAL
DISPLAY ON SCAN TOOL NORMAL CONDITION
TURN-SIG.LH
10
Turn-signal light
switch (RH)
T/S RH SW
OFF
11
Turn-signal light
switch (LH)
T/S LH SW
ON
30
Ignition switch
(IG1)
IG SW (IG1)
ON
TURN-SIG.RH
10
Turn-signal light
switch (RH)
T/S RH SW
ON
11
Turn-signal light
switch (LH)
T/S LH SW
OFF
30
Ignition switch
(IG1)
IG SW (IG1)
ON
ITEMS
ITEM
NO.
INPUT SIGNAL
DISPLAY ON SCAN TOOL NORMAL CONDITION
CENTR.DIS.AL
M
43
Tone alarm
BUZZER
ON
60
BEEP DATA
beep data
ON (2 kHz) (only
momentarily when switch is
operated)
KEY
REMND.ALM
30
Ignition switch
(IG1)
IG SW (IG1)
OFF
32
Front door switch
FRONT DOOR SW
ON
43
Tone alarm
BUZZER
ON
LGT
MONI.ALM
00
Headlight switch
HEADLIGHT SW
Either is on
01
Tail light switch
TAILLIGHT SW
30
Ignition switch
(IG1)
IG SW (IG1)
OFF
32
Front door switch
FRONT DOOR SW
ON
35
Headlight
automatic
shutdown function
H/L AUTO-CUT
OFF
43
Tone alarm
BUZZER
ON
OTHER
ALARM
30
Ignition switch
(IG1)
IG SW (IG1)
ON
43
Tone alarm
BUZZER
ON
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54Ba-18
• SUNROOF
• THEFT-ALARM
PULSE CHECK
M1549015100216
1. The input signals (signals other than SWS
communication line signals), which are
compatible with the SWS monitor by using the
scan tool or voltmeter, can be confirmed by the
Pulse Check. (Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
2. Use the scan tool or voltmeter to check the
following input signals.
NOTE: If a problem is found the Pulse Check,
proceed to the Problems during Input Signal
Check <Scan tool or voltmeter> (Refer to
Switches and their conditions, which are applicable
for Pulse Check
ITEM
ITEM
NO.
INPUT SIGNAL
DISPLAY ON SCAN TOOL NORMAL CONDITION
SUNROOF
OPE.
30
Ignition switch
(IG1)
IG SW (IG1)
ON
72
Response by the
sunroof-ECU
S/R ECU ACK
INPUT CHECK (only
momentarily when switch is
operated)
ITEM
ITEM
NO.
INPUT SIGNAL
DISPLAY ON SCAN TOOL NORMAL CONDITION
THEFT-ALARM 45
Theft-alarm
headlight
THEFTALM. H/L
ON
70
Response by the
front-ECU
FRONT ECU ACK
NORMAL ACK
INPUT SIGNAL
REQUIREMENT FOR SOUNDING
TONE ALARM
Key reminder switch
When the inserted ignition key is pulled
out
Hazard light switch
When the switch is turned from off to on
Seat belt which
When the seat belt is fastened
All door switches (excluding front door switch)
Either of the doors (excluding front door)
is opened
Driver's, front passenger's or back door lock key cylinder switch When the key cylinder is locked or
unlocked
Driver's, front passenger's, rear or back door lock actuator
When the driver's key cylinder or inside
lock knob is unlocked or locked
Door lock switch (incorporated in the power window main
switch)
When a door is locked or unlocked by a
door lock switch
Hood switch
When the hood is opened
Keyless entry system transmitter
Switches
When the switch is turned from off to on
CHECK AT ECU TERMINAL
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54Ba-19
CHECK AT ECU TERMINAL
M1549001200436
1. ETACS-ECU
NOTE: *: The terminal 1 to 20 connectors can not be
measured as the ETACS-ECU is installed directly on
the junction block. Therefore, this information is only
for reference.
19 20
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
21 22 23 24 25 26 27 28 29 30
31 32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48
49 50 51 52 53 54 55 56
ACX01511
*
AB
TERMINAL
NO.
INSPECTION ITEM
INSPECTION CONDITION
NORMAL VALUE
1
Output to rear wiper
When rear wiper is operating
Battery positive voltage
2
Power supply to ignition switch
(ACC)
Ignition switch: "ACC"
Battery positive voltage
3
Output to rear washer
When rear washer is operating
Battery positive voltage
4
Output to door lock
When door lock actuator is
operating (doors locked)
Battery positive voltage
5
Input of automatic stop signal to
rear wiper
When rear wiper is operating
Battery positive voltage
6
Battery power supply (for ECU)
Always
Battery positive voltage
7
Input from door switches
Either of door switches: ON
(Door open)
0 V
8
Output to power window relay
When the power windows can
work
2 V or less
9
Input from driver's door switch
Driver's door switch: ON (Driver's
door open)
0 V
11
Battery power supply (for turn-
signal light)
Always
Battery positive voltage
12
Battery positive voltage (for
central door lock)
Always
Battery positive voltage
14
Output to turn-signal light (LH)
When turn-signal light (LH) is on Battery positive voltage
15
Output to turn-signal light (RH)
When turn-signal light (RH) is on Battery positive voltage
16
Power supply to ignition switch
(IG1)
Ignition switch: "ON"
Battery positive voltage
17
Output to door unlock (excluding
direr's door)
When door lock actuator is
operating (doors unlocked)
Battery positive voltage
18
Output to dome light
When dome light is on
2 V or less
19
Output to door unlock (for
driver's door)
When driver's door lock actuator
is operating (doors unlocked)
Battery positive voltage
20
Ground (for ECU)
Always
0 V
21
SWS communication line
Always
0
− 12 V (pulse signal)
22
Input of diagnosis indication
selection
When scan tool is connected
0 V
23
Ground (for sensor)
Always
0 V
CHECK AT ECU TERMINAL
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54Ba-20
24
Input from fog light switch
Fog light switch: ON (When the
switch is depressed)
0 V
25
Input of driver's seat belt switch
signal
Driver's seat belt switch: ON
(seat belts unfastened)
0 V
26
Input of key reminder switch
signal
Key reminder switch: ON
(ignition key removed)
0 V
27
Input of hazard warning light
switch signal
Hazard warning light switch: ON
(When the switch is depressed)
0 V
28
Input of back door lock key
cylinder switch (LOCK) signal
Back door lock key cylinder
switch: LOCK
0 V
29
Input of front passengers's door
switch signal
Front passenger's door switch:
ON (Front passenger's door
open)
0 V
31
Output of data request signal
Always
0
− 5 V (pulse signal)
34
Input of signal from windshield
intermittent wiper interval
adjusting knob
Ignition switch: "ACC,"
Windshield intermittent wiper
interval adjusting knob: "FAST"
→ "SLOW"
0
→ 2.5 V
35
Input of "R" position signal from
transmission range switch
Ignition switch: "ON,"
Selector lever: "R"
Battery positive voltage
36
Output to ignition key hole
illumination light
When ignition key hole
illumination light is on
2 V or less
37
Output to data link connector
When DTC sets
0
− 12 V (pulse signal)
When input check signal is
output
0
− 12 V (when input
pulse signal is
fluctuating)
39
Output to seat belt warning light When seat belt warning light is
on
2 V or less
40
Output to the theft-alarm
indicator light
When the theft-alarm indicator
light is on
2 V or less
42
Output to horn
When a horn sounds by the
keyless entry horn answerback
function or the theft-alarm
system
2 V or less
45
Input of back door lock key
cylinder switch (UNLOCK) signal
Back door lock key cylinder
switch: UNLOCK
0 V
46
Input of front passenger's door
lock actuator switch (UNLOCK)
signal
Front passenger's door lock
actuator switch: UNLOCK
0 V
47
Input of rear and back door lock
actuator switch (UNLOCK)
signals
Rear or back door lock actuator
switch: UNLOCK
0 V
48
Input signal from the hood switch Hood switch: ON (Hood open)
0 V
49
Output to the theft-alarm horn
When theft-alarm horn is
sounding
2 V or less
TERMINAL
NO.
INSPECTION ITEM
INSPECTION CONDITION
NORMAL VALUE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст