Mitsubishi Montero (2002-2004). Manual — part 267
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-115
STEP 17. Check the harness wiring from ETACS-ECU
connector D-222 (terminal 17) to rear passenger's door
lock actuator (RH) connector H-21 (terminal 2).
AC204174
CONNECTOR : D-222
AB
1
2
3
5
6
4
9 8
121110
13
15 14
16
17
7
19
20
18
JUNCTION BLOCK SIDE
D-222
AC000316 AJ
CONNECTOR: H-21
REAR DOOR <RH>
1
2
3
4
5
6
H-21 (B)
H-21 (B)
(HARNESS SIDE)
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-116
NOTE: Also check junction block connector D-209 and inter-
mediate connector D-111 and F-23 for loose, corroded, or dam-
aged terminals, or terminals pushed back in the connector. If
junction block connector D-209 or intermediate connector D-
111 or F-23 are damaged, repair or replace the damaged com-
ponent(s) as described in GROUP 00E, Harness Connector
Inspection
.
Q: Is the harness wiring from ETACS-ECU connector D-222
(terminal 17) to rear passenger's door lock actuator (RH)
connector H-21 (terminal 2) in good condition?
YES : Replace the ETACS-ECU. Verify that all the doors
can be locked and unlocked normally.
NO : The harness wiring may be damaged or the
connectors may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the harness wiring as necessary. After repairs
have been made, verify that all the doors can now be
locked and unlocked normally.
AC203850
CONNECTOR: D-209
AE
D-209
D-209
JUNCTION BLOCK
(FRONT VIEW)
AC203860AC
D-111
CONNECTOR: D-111
D-111
AC204484
AC
CONNECTOR: F-23
F-23
F-23
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-117
STEP 18. Check the back door lock actuator.
1. Remove the back door lock actuator, and check it. Refer to
GROUP 42
− Back door Handle and Latch
2. Follow the table below to check the back door lock actuator
for correct operation.
Q: Is the back door lock actuator normal?
YES : Go to Step 19.
NO : Replace the back door lock actuator. Verify that all the
doors (including the back door) can be locked and
unlocked normally.
LEVER
POSITION
BATTERY
CONNECTION
LEVER
OPERATION
At the
"LOCK"
position
• Connect terminal 3
to the positive
battery terminal
• Connect terminal 2
to the negative
battery terminal
The lever moves
from the "LOCK"
position to the
"UNLOCK" position.
At the
"UNLOCK"
position
• Connect terminal 2
to the positive
battery terminal
• Connect terminal 3
to the negative
battery terminal
The lever moves
from the "UNLOCK"
position to the
"LOCK" position.
AC103292
A
VIEW A
UN
LOCK
LOCK
LEVER
AC
SYMPTOM PROCEDURES
TSB Revision
SWS SYMPTOM PROCEDURES
54Bb-118
STEP 19. Check ETACS-ECU connector D-222 and back
door lock actuator connector I-05 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are ETACS-ECU connector D-222 and back door lock
actuator connector I-05 in good condition?
YES : Go to Step 20.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that all the doors (including the back
door) can be locked and unlocked normally.
AC204174
CONNECTOR : D-222
AB
1
2
3
5
6
4
9 8
121110
13
15 14
16
17
7
19
20
18
JUNCTION BLOCK SIDE
D-222
ACX02293
CONNECTOR: I-05
AL
I-05 (B)
1 2 3
4 5 6
I-05 (B)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст