Mitsubishi Pajero Pinin. Manual — part 295
EXTERIOR –
Rear Wiper and Washer
51-16
INSTALLATION SERVICE POINT
"
A
A
WIPER ARM AND BLADE ASSEMBLY
INSTALLATION
Install so that the wiper blade is positioned at the shown position
when the wiper arm stops.
Standard value (A): 33
±
5 mm
"
B
A
GROMMET INSTALLATION
Align the mating mark of grommet and the notch of installation
hole.
INSPECTION
WIPER MOTOR CHECK
Disconnect the wiring harness connector, and check the wiper
motor operation with the wiper motor remaining installed to
the body.
Wiper Motor Operation
Connect a battery to the wiper motor as shown in the illustration
and check the motor operation.
Wiper Motor Stop Position
1.
Operate the wiper motor, and then disconnect the battery
to stop the wiper motor while the wiper motor is operating.
2.
Reconnect the battery as shown in the illustration, and
confirm that after the motor starts turning, it stops at the
automatic stop position.
WASHER MOTOR CHECK
1.
With the washer motor installed to the washer tank, fill
the washer tank with water.
2.
Check that the water squirts out strongly when system
voltage is applied to terminal 2 and terminal 1 is earthed.
Back
door
glass
ceramic
end line
A
Grommet
Mating mark
Notch
Operation check
Battery
Stop position check
Battery
EXTERIOR –
Rear Wiper and Washer/Headlamp Washer
51-17
WASHER FLUID EJECTION POINT CHECK
Adjust the ejection angle by moving the nozzle.
HEADLAMP WASHER
TROUBLESHOOTING
The headlamp washer is controlled by the Smart Wiring System (SWS). For troublesshooting, refer to
GROUP 54B – Troubleshooting.
HEADLAMP WASHER
REMOVAL AND INSTALLATION
4
6
1
2
2
7
4
5
3
3
2
2
2
2
3
3
8
5
Nozzle and check valve removal
steps
Draining of washer fluid
Front bumper (Refer to P.51-2.)
1. Check valve
2. Washer hose
3. Joint
4. Bracket
5. Nozzle
Washer tank removal steps
Draining of washer fluid
Air cleaner
Intake duct
6. Washer hose
7. Washer tank assembly
8. Headlamp washer motor
50 mm
50 mm
50 mm
Ceramic end line
Moulding
end line
EXTERIOR –
Headlamp Washer
51-18
INSPECTION
CHECK VALVE CHECK
Apply pressure to the inlet of the check valve to check its
opening pressure.
Opening pressure: 78 kPa
HEADLAMP WASHER MOTOR CHECK
1.
With the washer motor installed to the washer tank, fill
the washer tank with water.
2.
Connect battery (+) and (–) cables to terminals (1) and
(2) respectively to see that the washer motor runs and
water is injected.
EXTERIOR –
Marks
EXTERIOR –
Marks
51-19
MARKS
REMOVAL AND INSTALLATION
1
2
7
6
5
4
3
4
3
1. Three diamonds mark
2. “GDI” mark
3. Pininfarina mark
4. Pininfarina logo mark
"
A
A
5. Vehicle name decal
"
A
A
6. Three diamonds mark
"
A
A
7. “GDI” mark
INSTALLATION SERVICE POINT
"
A
A
INSTALLATION OF MARKS
1.
APPLICATION POSITION
(5) Vehicle name decal
<Vehices except for Spain>
<Vehicles for Spain>
Back door end line
Align the application tape end with this slit.
Slit
Back door end line
Align the application tape end with this slit.
Slit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст