Mitsubishi Pajero Pinin. Manual — part 274
BODY –
Door
BODY –
Door
42-22
DOOR ASSEMBLY
REMOVAL AND INSTALLATION
Post-installation Operation
Door Fit Adjustment (Refer to P.42-19.)
21 Nm
23 Nm
6
7
9
8
3
4, 5
4
1
5
2
15 Nm
12 Nm
Door assembly removal steps
1. Harness connector
2. Door check connecting bolt
3. Door assembly
4. Door upper hinge
5. Door lower hinge
Striker removal steps
6. Striker
7. Striker shim
Door switch removal steps
8. Door switch cap
9. Door switch
INSPECTION
DOOR SWITCH CONTINUITY CHECK
Driver’s side
Switch
Terminal number
Switch
position
1
2
3
(Earth)
Released (ON)
Depressed (OFF)
BODY –
Door
BODY –
Door
42-23
Passenger’s side
Switch
iti
Terminal number
position
1
2 (Earth)
Released (ON)
Depressed (OFF)
DOOR TRIM AND WATERPROOF FILM
REMOVAL AND INSTALLATION
6
7
3
2
1
14
10
8
9
16
12
13
17
18
10
15
11
5
4
Sealant:
3M ATD Part No. 8625 or equivalent
<Vehicles with
power windows>
<Vehicles without
power windows>
14
18
Removal steps
A
A
"
1. Power window and remote-
controlled mirror switch assembly
2. Power window switch panel
assembly
3. Power window switch
4. Remote-controlled mirror switch
A
B
"
5. Door inside handle cover
6. Delta cover, inner
A
C
" "
B
A
7. Clip
"
B
A
8. Escutcheon
"
B
A
9. Regulator handle
10. Cap
11. Door trim
12. Grip bracket
13. Door grip
14. Front arm restraint cover
15. Door lamp lense
16. Speaker
17. Power window switch bracket
"
A
A
18. Waterproof film
BODY –
Door
42-24
CLIP AND CLAW POSITIONS
Delta cover,
inner
Delta
cover,
inner,
door trim
Claw
Cap
Claw
Cap
Door
panel
Clip
C
C
Section A – A
Section B – B
Section C – C
View D
View B
View C
View E
A
A
Door trim
B
B
Door trim
Door lamp lense
Door trim
View C
View D
View A
View B
A
A
View A
Claw
Power window and remote-controlled
mirror switch assembly
Clip
Front arm
restraint cover
Power window and remote-controlled-
mirror switch assembly
Front arm
restraint cover
D
D
E
E
View E
Section D – D
Section E – E
: Claws positions
: Clips positions
NOTE
BODY –
Door
42-25
REMOVAL SERVICE POINTS
A
A
"
POWER WINDOW AND REMOTE-CONTROLLED
MIRROR SWITCH ASSEMBLY/POWER WINDOW
SWITCH PANEL ASSEMBLY REMOVAL
1.
Use the special tool to pry out the power window and
remote-controlled mirror switch assembly, first at the front
and then at the rear. (Refer to P.42-24, CLAW AND CLIP
POSITIONS.)
2.
Use a flat-tipped screwdriver to disengage the lower claws
of the power window and remote-controlled mirror switch
assembly as shown in the illustration, and then remove
the power window and remote-controlled mirror switch
assembly.
A
B
"
DOOR INSIDE HANDLE COVER REMOVAL
Use the special tool to pry out the rear part of door inside
handle cover, and then slide the door inside handle cover
in the direction of arrow shown to remove it.
A
C
"
CLIP REMOVAL
Use a cloth to remove the clip as shown in the illustration.
INSTALLATION SERVICE POINTS
"
A
A
WATERPROOF FILM INSTALLATION
Apply the specified sealant to the shown positions of waterproof
film, and then attach the waterproof film.
Specified sealant: 3M ATD Part No. 8625 or equivalent
Caution
Be sure to apply the sealant below the inner panel water
drain holes so as not to plug them.
MB990784
Claw
Door
trim
Switch bracket
Claw
Flat-tipped
screw driver
Power window and remote-controlled switch assembly
Section A – A
MB990784
A
A
A
A
Door trim
Claw
Waterproof film
Inner panel
water drain
hole
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст