Mitsubishi Pajero Pinin. Manual — part 342
CHASSIS ELECTRICAL –
Multi-Center Display <High Grade>
54A-84
(4) The next mode is the sensor checking mode. Press the
F1 switch to start sensor checking.
If you would like to proceed to the next checking operation
without carrying out sensor checking, press the F6 switch.
(5) When sensor checking starts, the gyro output will be
checked first while the vehicle is stopped, so make sure
that the vehicle is stopped for this check.
If the vehicle is moving when the sensor checking starts,
the vehicle speed sensor will be shown as defective.
Follow the guidance message on the multi-center display.
(6) Next, drive the vehicle for approximately 10 meters while
changing the running direction in order to check the vehicle
speed pulse and the gyro sensor output. The sensor
checking will then be completed. If there is an open circuit
in the vehicle speed sensor, sensor checking will not
complete even after the vehicle has travelled more than
10 meters. In this case, press the F5 switch to stop
checking.
If the vehicle does not move or there is an open circuit
in vehicle speed sensor, the vehicle speed sensor will
be shown as defective.
(7) When sensor checking is completed, the check results will
appear on the screen. After checking the results, press the
F1 switch to proceed to the next check.
(8) The next mode is the vehicle signal checking mode. The
lighting switch condition, ignition key position, shift lever
selection (R or a position other than R) and the power
supply voltage drop will be appear on the screen. Check
that the details displayed match the actual vehicle signals,
and then press the F1 switch.
If the vehicles does not move or there is an open circuit
in vehicle speed sensor, the vehicle speed sensor will
be shown as defective.
CHASSIS ELECTRICAL –
Multi-Center Display <High Grade>
54A-85
(9) The next mode is speaker checking mode. The test sound
will be output alternately from each speaker each time
the F2 switch is pressed.
At the early mass production, sometimes radio sound will
be output. This is not a sign of abnormality.
(10)Press the F1 switch to end service mode. The screen
will change to navigation mode.
3.
MONITOR CHECKING
(1) If the F6 switch is pressed at the service mode initial
screen, monitor checking will start.
CHASSIS ELECTRICAL –
Multi-Center Display <High Grade>
54A-86
(2) A colored bar will appear on the screen.
Press a function switch to change to another screen. The
screen will return to the service mode initial screen if the F1
switch is pressed.
4.
AUDIO CHECKING
(1) If the F5 switch is pressed at the service mode initial
screen, the audio checking menu screen will appear.
(2) Next, press the function switches to carry out audio
checking.
CHASSIS ELECTRICAL –
Multi-Center Display <High Grade>
54A-87
(3) Press the F3 switch to display the speaker checking screen.
The test sound will be output alternately from each speaker
each time the F2 switch is pressed.
Press the F1 switch to end speaker checking and return to
the audio checking menu screen.
At the early mass production, sometimes radio sound will
be output. This is not a sign of abnormality.
(4) Press F4 to display the audio key checking screen.
When one of the audio switches is pressed, the screen
display color for that switch should change. This indicates
that this particular switch system is working normally.
Press the F1 switch to check the operation of the F1 switch.
Press the F1 switch once more to return to the audio
checking menu screen.
5.
SELF-DIAGNOSIS
(1) If the F5 switch is pressed at the service mode initial
screen, the self-diagnosis menu screen will appear.
(2) Next, use the function switches to carry out self-diagnosis.
(3) When the F5 switch is pressed, self-diagnosis for the wiring
is carried out.
A colored bar will appear on the screen of the Multi-center
Display unit, and all units which are connected to the
navigation unit will be checked during this time.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст