Mitsubishi Pajero Pinin. Manual — part 343
CHASSIS ELECTRICAL –
Multi-Center Display <High Grade>
54A-88
(4) Once the transmission checking is completed, the results
of checking will appear on the screen.
After checking the results, press the F1 switch to return to
the self-diagnosis menu screen.
(5) If the F6 switch is pressed at the self-diagnosis menu
screen, sensor checking will start.
Press the F1 switch to start sensor checking.
If you would like to return to the self-diagnosis menu screen
without carrying out sensor checking, press the F5 switch.
(6) When sensor checking starts, the gyro output will be
checked first while the vehicle is stopped, so make sure
that the vehicle is stopped for this check.
If the vehicle is moving when the sensor checking starts,
the vehicle speed sensor will be shown as defective.
Follow the guidance message on the multi-center display.
(7) Next, drive the vehicle for approximately 10 meters while
changing the running direction in order to check the vehicle
speed pulse and the gyro sensor output. The sensor
checking will then be completed. If there is an open circuit
in the vehicle speed sensor, sensor checking will not
complete even after the vehicle has travelled more than
10 meters. In this case, press the F5 switch to stop
checking.
If the vehicle does not move or there is an open circuit
in vehicle speed sensor, the vehicle speed sensor will
be shown as defective.
CHASSIS ELECTRICAL –
Multi-Center Display <High Grade>
54A-89
(8) When sensor checking is completed, the check results
will appear on the screen. After checking the results, press
the F1 switch to return to the self-diagnosis menu screen.
(9) If the F6 switch is pressed at the self-diagnosis menu
screen, vehicle signal checking will start.
The lighting switch condition, ignition key position, shift
lever selection (R or a position other than R) and the
power supply voltage drop will be appear on the screen.
Press the F1 switch to return to the self-diagnosis menu
screen.
If the F2 switch is pressed at the self-diagnosis menu
screen, version data self-diagnosis will be carried out,
and the check results will appear on the screen.
Press the F1 switch to return to the self-diagnosis menu
screen.
6.
DIAGNOSIS RECORDING
(1) If the F6 switch is pressed at the service mode initial
screen, the diagnosis recording screen will appear.
(2) Press the F1 switch to return to the service mode initial
screen.
(3) Press the F6 switch to clear any error codes which may
still be remaining from diagnosis recording.
When this is done, the clearing confirmation screen will
appear. If it is okay to continue with the clear, press the
F5 switch. To cancel clearing, press the F6 switch.
If the F6 switch is pressed, the screen will return to the
diagnosis recording screen.
CHASSIS ELECTRICAL –
Multi-Center Display <High Grade>
54A-90
(4) If the F5 switch is pressed, all past error codes will be
cleared, and the screen will return to the diagnosis
recording screen. The Clear button will not be displayed
at this time.
(5) Press the F1 switch to return to the service mode initial
screen.
7. ERROR CODE TABLE
Error Code No.
Error Details
Detection Method (Reference)
Reference
Page
1011
Ambient temperature sensor not connected
during diagnosis
Connection checking
54A-105
1021
Fuel gauge not connected during diagnosis
Connection checking
54A-106
1031
GPS abnormality during diagnosis
Connection checking
54A-106
1041
Engine-ECU not connected during diagnosis
Connection checking
54A-106
1051
SWS not connected during diagnosis
(This error does not occur when correct car
type is set)
Connection checking
54A-106
1091
CD drive too hot during diagnosis
Connection checking
54A-106
1092 – 1096
CD drive abnormality during diagnosis
Connection checking
54A-107
10A1, 10B1
Memory of navigation unit abnormality during
diagnosis
Connection checking
54A-107
20D1, 30D1
Vehicle speed pulse abnormality during
diagnosis
Sensor checking
54A-107
20E1, 20E2,
30E1, 30E2
Gyro level abnormality during diagnosis
Sensor checking
54A-107
CHASSIS ELECTRICAL –
Multi-Center Display <High Grade>
54A-91
MAIN UNIT TERMINAL VOLTAGES
1.
MULTI-CENTER DISPLAY UNIT
Termi-
nal No
Input/
Output
Signal Symbol
Terminal
Voltage
Harness Problem
Trouble Symptom Resulting from
Harness Problem
nal
No.
Output
Voltage
(V)
Open
Circuit
Short-
circuit
Harness
Problem
1
Input
G+SYTNC (AUDIO)
–
f
f
Noise display (random dot pattern)
2
Input
B+SYNC (AUDIO)
–
f
f
Blue, white, cyan and magenta do not
appear in RGB screen.
3, 4
–
–
–
–
–
–
5
Input
ISOK
Hi:
System
voltage
Lo: 0 – 1
f
f
MUT-
II
cannot be used to check
engine-ECU.
6
Input/
Output
DATA
Hi:
System
voltage
Lo: 0 –1
f
f
Switch operation sound buzzer does
not peep.
7
Input/
Output
M–DATA (AUDIO)
Hi: 4 – 5
Lo: 0 – 1
f
f
Buzzer sounds 30 seconds after the
power turned to on. Nighttime
illumination does not appear for any
navigation system.
8
Input/
Output
M–CLOCK (AUDIO)
Hi: 4 – 5
Lo: 0 – 1
f
f
Buzzer sounds 30 seconds after the
power turned to on. Nighttime
illumination does not appear for any
navigation system.
9, 10
–
–
–
–
–
–
11
–
SHIELD–GND
–
–
–
–
12
–
–
–
–
–
–
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст