Mitsubishi Pajero Pinin. Manual — part 173
AUTOMATIC TRANSMISSION –
Service Specifications/
Lubricants/Sealants and Adhesives
23-2
SERVICE SPECIFICATIONS
Items
Standard value
Clearance between inner cable stopper and dust cover end surface mm
0.8 – 1.5
Input shaft speed sensor resistance (at 20
_
C)
Ω
620
$
60
Output shaft speed sensor resistance (at 20
_
C)
Ω
430
$
43
A/T fluid temperature sensor resistance
Ω
at 25
_
C
1,100
at 120
_
C
57
Coil resistance of solenoid valve No.1 (at 25
_
C)
Ω
13
$
2
Coil resistance of solenoid valve No.2 (at 25
_
C)
Ω
13
$
2
Coil resistance of solenoid valve No.3 (at 25
_
C)
Ω
13
$
2
Stall speed r/min
2,320 – 2,620
Line pressure kPa
at idle speed
D range
373 – 422
R range
520 – 579
at stall speed
D range
765 – 863
R range
1,383 – 1,628
LUBRICANTS
Items
Specified lubricant
Quantity
ȏ
Transmission fluid
DEXRON
II
or equivalent
7.2
Transfer oil
Hypoid gear oil SAE 75W-90 or
75W-85W conforming to API GL-4
2.3
SEALANTS AND ADHESIVES
Items
Specified sealant
Remarks
Transfer control lever gasket
3M ATD Part No.8660 or equivalent
Semi-drying sealant
Transfer control lever assembly
installation bolt
3M Stud Locking No.4170 or
equivalent
Anaerobic sealant
AUTOMATIC TRANSMISSION –
Special Tools
23-3
SPECIAL TOOLS
Tool
Number
Name
Use
MB991502
MUT-
II
sub
assembly
Checking of the diagnosis code
MD998330
(including
MD998331)
Oil pressure gauge
(2,942 kPa)
Measurement of oil pressure
MD998920
Adapter
Connection of oil pressure gauge
AUTOMATIC TRANSMISSION –
Troubleshooting <A/T>
23-4
TROUBLESHOOTING <A/T>
STANDARD FLOW OF DIAGNOSIS TROUBLESHOOTING
Gathering information from custom-
er.
Check trouble symptoms.
Read the diagnosis code (GROUP
00 – How to Use Troubleshooting/In-
spection Service Points.)
Communication with
MUT-
II
not possible
Inspection procedure No. 1 in
Inspection Chart For Trouble
Symptoms (Refer to P.23-16.)
Diagnosis code
displayed
Erase the diagnosis code (GROUP
00 – How to Use Troubleshooting/In-
spection Service Points.)
Carry out the essential service
(Refer to P.23-34.)
Road test (Refer to P.23-6.)
Abnormality exists (no diagnosis code)
No abnormality
Recheck diagnosis codes which
were read before the road test.
Abnormality exists
(diagnosis code
present)
Diagnosis
code displayed
No diagnosis
code displayed
To INSPECTION CHART FOR
DIAGNOSIS CODES
(Refer to P.23-9.)
To INSPECTION CHART FOR
TROUBLE SYMPTOMS
(Refer to P.23-15.)
Search for cause.
Found
Not found
Repair
Confirmation test (road test)
NG
NG
INTERMITTENT MALFUNCTION
(GROUP 00 – Points to Note for
Intermittent Malfunctions.)
OK
Completed
OK
Check automatic transmission fluid
NG
Replace automatic transmission
fluid.
OK
NO diagnosis code displayed
AUTOMATIC TRANSMISSION –
Troubleshooting <A/T>
23-5
DIAGNOSIS FUNCTION
N RANGE LAMP
The N range lamp flashes at a frequency of approximately
1 Hz if there is an abnormality in any of the items in the
table below which are related to the A/T system. Check the
diagnosis code output if the N range lamp is flashing at a
frequency of approximately 1 Hz.
N range lamp flashing items
Input shaft speed sensor
Output shaft speed sensor
Each solenoid valve
Caution
If the N range lamp is flashing at a frequency of
approximately 2 Hz (faster than at 1 Hz), it means that
the A/T fluid temperature is too high. Stop the vehicle
in a safe place and wait until the N range lamp switches
off.
METHOD OF READING THE DIAGNOSIS CODE
Use the MUT-
II
or the N range lamp to take a reading of
the diagnosis codes. (Refer to GROUP 00 – How to Use
Troubleshooting/Inspection Service Points.)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст