Mitsubishi Pajero Pinin. Manual — part 171
MANUAL TRANSMISSION
–
Transmission Control
22-7
C
STOPPER BRACKET ASSEMBLY INSTALLATION
1.
Eliminate sealant and adhesive adhered to the stopper
bracket assembly installation bolts.
2.
Use a tap (M8
1.25) to eliminate adhesive adhered
to the threaded holes of the stopper bracket assembly
installation nuts, and then clean the holes with a
compressed air.
3.
Apply the specified sealant to the stopper bracket assembly
installation bolts (A shown in the illustration) and the
specified adhesive to the threaded part of the stopper
bracket assembly installation bolts (B shown in the
illustration), and then install the stopper bracket assembly.
Specified sealant (A):
3M ATD Part No.8660 or equivalent
Specified adhesive (B):
3M Stud Locking No.4170 or equivalent
A
B
MANUAL TRANSMISSION
–
Transmission and Transfer Assembly
22-8
TRANSMISSION AND TRANSFER ASSEMBLY
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Transmission Oil and Transfer Oil Draining and
Refilling (Refer to P.22-2, 3.)
Transmission Control Lever Assembly and Transfer
Control Lever Assembly Removal and Installation
(Refer to P.22-4.)
Front Propeller Shaft and Rear Propeller Shaft
Removal and Installation (Refer to GROUP 25.)
Front Exhaust Pipe and Catalytic Converter Removal
and Installation (Refer to GROUP 17 – Emission
Control.)
Shift Lever Operation Check <only after installation>
Instruments Operation Check <only after installation>
48 Nm
48 Nm
19 Nm
6
1
2
5
4
30 Nm
7
3
6
48 Nm
48 Nm
48 Nm
5
Removal steps
1. Clutch release cylinder installation
bolts
2. Starter motor installation bolts
3. Oil pan connection bolts
Adapter (Refer to GROUP 32 –
Transmission mount.)
4. Transmission harness connector
connection
5. Transmission assembly upper cou-
pling bolts
6. Transmission assembly lower cou-
pling bolts
7. Transmission and transfer assembly
MANUAL TRANSMISSION
–
4WD Indicator Control Unit
22-9
4WD INDICATOR CONTROL UNIT
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Seat Assembly (Driver’s side) and Rear Seat Cushion
Removal and Installation (Refer to GROUP 52A –
Seat.)
Front Scuff Plate (Right) and Quarter Trim (Right)
Removal and Installation (Refer to GROUP 52A –
Trims.)
Front Floor Console and Rear Floor Console Removal
and Installation (Refer to GROUP 52A.)
1
2
2
5 Nm
4
3
2
Removal steps
1. Rear heater duct (right)
Turn up the carpet.
2. Harness connector connection
3. 4WD indicator control unit
4. Bracket
MANUAL TRANSMISSION
–
4WD Indicator Control Unit
22-10
NSPECTION
4WD INDICATOR CONTROL UNIT CHECK
Measure terminal voltage on each condition. Connect the harness to the control unit. Insert the probe
from the back side of the connector and measure the voltage between the terminal No.8 (earth terminal)
and each terminal.
Front wheel lamp
VCU lock lamp
Rear wheel lamp
Termi-
nal No.
Check item
Check condition
1: Ignition switch
Check condition 2:
Transfer lever position
Normal
condition
1
High/Low detection switch
ON
Move from 4HL
C
to
4LL
C
or vice versa
System voltage*
4HL
C,
4LL
C
0 V
2
4WD operation detection switch
ON
2H
System voltage*
4H
0 V
3
Ignition switch
OFF
–
0 V
ON
–
System voltage
4
4WD indicator
lamp
VCU lock lamp
ON
4H
System voltage
lamp
4HL
C
1.5 V or lower
5
VCU lock detection switch
ON
4H
System voltage*
4HL
C
0 V
6
Free wheel engage switch
ON
2WD condition
System voltage*
4WD condition
0 V
7
VCU lock operation detection switch
ON
4H
System voltage*
4HL
C
0 V
9
4WD indicator
lamp
Rear wheel
ON
Move from 4HL
C
to
4LL
C
or vice versa
0 V
4HL
C,
4LL
C
System voltage*
10
4WD indicator
lamp
Front wheel
ON
2WD condition
0 V
lamp
4WD condition
System voltage*
NOTE
System
voltage marked with * is low slightly (from 1 V to 2 V).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст