Mitsubishi Pajero Pinin. Manual — part 233
REAR SUSPENSION –
Stabilizer Bar
34-3
INSTALLATION SERVICE POINT
A
STABILIZER BAR/BUSHING/STABILIZER
BRACKET INSTALLATION
Align the identification mark of stabilizer bar with the left end
of the bushing, before tightening the mounting bolts.
INSPECTION
STABILIZER LINK BALL JOINT TURNING TORQUE
CHECK
1.
After shaking the ball joint stud several times, install the
nut to the stud and use the special tools to measure the
turning torque of the ball joint.
Standard value: 1.7 – 3.1 Nm
2.
When the measured value exceeds the standard value,
replace the stabilizer link.
3.
When the measured value is lower than the standard value,
check that the ball joint turns smoothly without excessive
play. If so, it is possible to reuse that ball joint.
STABILIZER LINK BALL JOINT DUST COVER CHECK
1.
Check the dust cover for cracks or damage by pushing
it with finger.
2.
If the dust cover is cracked or damaged, replace the
stabilizer link.
NOTE
Cracks or damage of the dust cover may cause damage
of the ball joint. When it is damaged during service work,
replace the dust cover.
STABILIZER LINK BALL JOINT DUST COVER
REPLACEMENT
Only when the dust cover is damaged accidentally during
service work, replace the dust cover as follows:
1.
Remove the clip ring and the dust cover.
2.
Apply multipurpose grease to the inside of the dust cover.
3.
Wrap plastic tape around the stabilizer link stud, and then
install the dust cover to the stabilizer link.
4.
Secure the dust cover by the clip ring.
5.
Check the dust cover for cracks or damage by pushing
it with finger.
Front of vehicle
Identification mark
MB990326
MB990968
Clip ring
BASIC BRAKE
SYSTEM
Click on the applicable bookmark to selected the required model year
35A-2
BASIC BRAKE
SYSTEM
CONTENTS
GENERAL INFORMATION
3
. . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS
4
. . . . . . . . . . . . . . . . .
LUBRICANTS
5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SEALANT
5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS
5
. . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE
6
. . . . . . . . . . . . . . . . . . . . .
Brake Pedal Check and Adjustment
6
. . . . . . . . . . . .
Brake Booster Operating Test
7
. . . . . . . . . . . . . . . . . .
Check Valve Operation Check
8
. . . . . . . . . . . . . . . . .
Load Sensing Spring Length Check and
Adjustment 8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load Sensing Proportioning Valve Function
Test 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bleeding
10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Fluid Level Sensor Check
10
. . . . . . . . . . . . .
Disc Brake Pad Check and Replacement
11
. . . . . .
Disc Brake Rotor Check
12
. . . . . . . . . . . . . . . . . . . . .
Brake Disc Thickness Check
12
. . . . . . . . . . . . . . . . .
Brake Disc Run-out Check and Correction
13
. . . .
BRAKE PEDAL
14
. . . . . . . . . . . . . . . . . . . . . . . . . . .
MASTER CYLINDER AND BRAKE
BOOSTER
15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master Cylinder
19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRONT DISC BRAKE
20
. . . . . . . . . . . . . . . . . . . . .
REAR DISC BRAKE
25
. . . . . . . . . . . . . . . . . . . . . . .
LOAD SENSING PROPORTIONING
VALVE 31
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BASIC BRAKE SYSTEM –
General Information
35A-3
GENERAL INFORMATION
The brake system offers high dependability and durability along with improved braking performance and
brake sensitivity.
Items
Specifications
Master cylinder
Type
Tandem type
I.D. mm
22.2
Brake booster
Type
Vacuum type, single
Effective dia. of power cylinder mm
230
Boosting ratio
4.5
Load sensing proportioning
valve
Type
Dual type
valve
Decompression ratio
0.25
Front disc brakes
Type
Floating caliper, 1-piston, ventilated disc
Disc effective dia.
×
thickness mm
236
×
22
Wheel cylinder I.D. mm
57.2
Pad thickness mm
10.0
Clearance adjustment
Automatic
Rear disc brakes
Type
Floating caliper,1-piston, solid disc
Disc effective dia.
×
thickness
222
×
9.4
Wheel cylinder I.D. mm
34.93
Pad thickness mm
10.0
Clearance adjustment
Automatic
Brake fluid
DOT3 or DOT4
CONSTRUCTION DIAGRAM
Brake booster
Master cylinder
Load sensing
proportioning
valve
Hydraulic unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст