Mitsubishi Eclipse. Manual — part 747
TRANSAXLE ASSEMBLY
TSB Revision
MANUAL TRANSAXLE
22A-23
(2) Set the engine hanger (special tool MB991928) to the
front fender mounting bolts (A and B) and the radiator
support upper insulator mounting bolts (C and D), which
are located in the engine compartment, as shown.
NOTE: Adjust the engine hanger balance by sliding the
slide bracket (HI).
(3) Set special tools MB991454 to hold the engine/transaxle
assembly.
.
<<I>> TRANSAXLE ASSEMBLY REMOVAL
CAUTION
Do not remove the flywheel mounting bolt shown by the
arrow. If this bolt is removed, the flywheel will become out
of balance and damaged.
AC106454AB
A
B
C
D
AC302400AC
MB991928
SLIDE BRACKET (HI)
MB991454
MB991932
MB991931
MB991933
MB991929
MB991930
AC001669
BOLT
AB
FLYWHEEL
TRANSAXLE ASSEMBLY
TSB Revision
MANUAL TRANSAXLE
22A-24
INSTALLATION SERVICE POINTS
.
>>A<< TRANSAXLE ASSEMBLY INSTALLATION
CAUTION
On the pull-type clutch, do not roll the transaxle assembly
when installing it to the engine. If the transaxle assembly
is rolled, the wedge collar and the wire ring will be
deformed, causing a clutch malfunction due to improper
engagement of the wedge collar and the wire ring.
.
>>B<< TRANSAXLE MOUNT STOPPER INSTALLATION
Install the transaxle mount stopper so that the arrow mark
points as shown in the illustration.
.
AC001670
ENGINE SIDE
TRANSAXLE SIDE
FLYWHEEL
CLUTCH COVER
WEDGE
COLLAR
RELEASE
BEARING
WIRE RING
AB
AC001647AB
TRANSAXLE
MOUNT
STOPPER
ENGINE SIDE
ARROW
TRANSAXLE
MOUNT
BRACKET
TRANSAXLE ASSEMBLY
TSB Revision
MANUAL TRANSAXLE
22A-25
>>C<< CLUTCH RELEASE BEARING CONNECTION
1. Move the release fork to the "A" direction, and engage the
release bearing with the wedge collar.
2. When the release fork is moved to the "B" direction, the
release fork should drag.
AC001671AC
A
FLYWHEEL
CLUTCH COVER
RELEASE
BEARING
WIRE RING
B
RELEASE FORK
WEDGE
COLLAR
FRONT
EXHAUST
PIPE
SPECIFICATIONS
TSB Revision
MANUAL TRANSAXLE
22A-26
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1221006600164
LUBRICANT
M1221000400173
ITEM
SPECIFICATION
Transaxle assembly
Bell housing cover (to engine)
8.8
± 1.0 N⋅m (78 ± 9 in-lb)
Bell housing cover (to transaxle)
26
± 4 N⋅m (19 ± 3 ft-lb)
Center bearing bolt
40
± 5 N⋅m (30 ± 3 ft-lb)
Centermember attaching bolt
front side
93
± 15 N⋅m (69 ± 11 ft-lb)
rear side
74
± 4 N⋅m (55 ± 3 ft-lb)
Clutch release cylinder
18
± 3 N⋅m (13 ± 2 ft-lb)
Front roll stopper bracket nut
45
± 10 N⋅m (34 ± 7 ft-lb)
Lower arm nut
108
± 10 N⋅m (80 ± 7 ft-lb)
Rear roll stopper bracket attaching bolt
45
± 5 N⋅m (34 ± 3 ft-lb)
Rear roll stopper bracket nut
45
± 5 N⋅m (34 ± 3 ft-lb)
Shift cable and select cable assembly bracket bolt
18
± 3 N⋅m (13 ± 2 ft-lb)
Stabilizer link nut
44
± 10 N⋅m (33 ± 7 ft-lb)
Starter motor
30
± 3 N⋅m (23 ± 2 ft-lb)
Tie rod end nut
29
± 4 N⋅m (21 ± 4 ft-lb)
Transaxle assembly lower part coupling bolt
2.4L ENGINE
48
± 5 N⋅m (36 ± 4 ft-lb)
3.0L ENGINE
88
± 10 N⋅m (65 ± 7 ft-lb)
Transaxle assembly upper part coupling bolt
2.4L ENGINE
48
± 5 N⋅m (36 ± 3 ft-lb)
Transaxle assembly upper part coupling bolt (bolt, flange) 3.0L ENGINE
74
± 9 N⋅m (54 ± 7 ft-lb)
Transaxle assembly upper part coupling bolt (bolt, washer
assembly)
3.0L ENGINE
88
± 10 N⋅m (65 ± 7 ft-lb)
Transaxle mount bracket attaching nut
57
± 7 N⋅m (42 ± 5 ft-lb)
Transaxle mount stopper attaching nut
81
± 12 N⋅m (60 ± 9 ft-lb)
Transmission oil drain plug
32
± 2 N⋅m (24 ± 1 ft-lb)
Transmission oil filler plug
32
± 2 N⋅m (24 ± 1 ft-lb)
Upper oil pan connecting bolt
35
± 6 N⋅m (26 ± 4 ft-lb)
Transaxle control
Lever base bracket attaching bolt
12
± 2 N⋅m (102 ± 22 in-lb)
M/T cable attaching bolt
12
± 2 N⋅m (102 ± 22 in-lb)
Retainer nut
5.0
± 1.0 N⋅m (44 ± 9 in-lb)
Select lever attaching bolt
6.0
± 2.0 N⋅m (53 ± 18 in-lb)
ITEM
SPECIFIED LUBRICANTS
QUANTITY
Transaxle oil dm
3
(qt)
F5M42
Gear oil API classification GL-4 SAE
75W
− 85W or 75W − 90
2.2 (2.3)
F5M51
2.8 (3.0)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст