Mitsubishi Eclipse. Manual — part 919
REVERSE AND OVERDRIVE CLUTCH
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-59
>>C<< CLUTCH PLATE/CLUTCH DISC/CLUTCH REACTION
PLATE INSTALLATION
CAUTION
Immerse the clutch disc in ATF before assembling it. IF the
clutch disc is new, soak it in ATF for at least two hours.
1. Assemble the four clutch plates and four clutch discs one on
top of the other inside the underdrive clutch retainer. All four
clutch plates should be assembled so that the places with no
teeth (marked "A") are aligned with the holes in the retainer
(marked "B").
2. Install the clutch reaction plate in the direction shown.
in stall it the same as the clutch plates, so that the areas with
no teeth (marked "A") are aligned with the retainer (marked
"B").
.
>>D<< SNAP RING INSTALLATION
1. Install the snap ring into the groove of clutch retainer.
2. Set special tools MB991628 <F4A42>, MB991629 <F4A51>
and MD998924 as shown in the illustration, and then
compress the clutch element.
3. Check that the clearance between the snap ring and the
clutch reaction plate is within the standard value. If not within
the standard value, select a snap ring so that it is.
Standard value: 1.6
− 1.8 mm (0.0630 − 0.0709 inch)
REVERSE AND OVERDRIVE CLUTCH
DISASSEMBLY AND ASSEMBLY
M1233024800020
NUMBER OF CLUTCH DISCS AND PLATES
AKX01044
B
A
AB
AKX01105
CLUTCH PLATES
ROUNDED EDGE
PISTON
SIDE
CLUTCH DISCS
AB
CLUTCH
REACTION
PLATE
AKX01045
MB991628
<F4A42>
OR
MB991629
<F4A51>
MD998924
AB
MODEL
PRESSURE
PLATE
CLUTCH DISC
CLUTCH PLATE CLUTCH
REACTION PLATE
Over drive clutch
F4A42
−
4
4
1
F4A51
1
4
3
1
Reverse clutch
−
2
2
1
REVERSE AND OVERDRIVE CLUTCH
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-60
Required Special Tools:
• MB991628: Spring Compressor <F4A42>
• MB991629: Spring Compressor <F4A51>
• MB991789: Spring Compressor <F4A51>
• MB991790: Spring Compressor <F4A42>
• MD998924: Spring Compressor Retainer
• MD999590: Spring Compressor
AKX01127
APPLY AUTOMATIC
TRANSMISSION FLUID
TO ALL MOVING PARTS
BEFORE INSTALLATION.
17
20
19
18
17
16
14
13
12
11
10
15
19
18
13
16
14
20
10
11
15
12
7
3
5
8
6
4
2
1
1 2
4
5
6
8
7
3
8 <F4A42> or 9 <F4A51>
8 <F4A42> or
9 <F4A51>
AB
DISASSEMBLY STEPS
>>G<<
1.
SNAP RING
>>F<<
2.
CLUTCH REACTION PLATE
>>F<<
3.
CLUTCH DISC
>>F<<
4.
CLUTCH PLATE
>>E<<
5.
SNAP RING
>>D<<
6.
CLUTCH REACTION PLATE
>>D<<
7.
CLUTCH DISC
>>D<<
8.
CLUTCH PLATE
9.
PRESSURE PLATE <F4A51>
<<A>>
>>C<<
10. SNAP RING
11. SPRING RETAINER
>>A<<
12. D-RING
13. RETURN SPRING
14. OVERDRIVE CLUTCH PISTON
>>A<<
15. D-RING
>>B<<
16. REVERSE CLUTCH PISTON
>>A<<
17. D-RING
>>A<<
18. D-RING
>>A<<
19. D-RING
20. REVERSE CLUTCH RETAINER
DISASSEMBLY STEPS
REVERSE AND OVERDRIVE CLUTCH
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-61
DISASSEMBLY SERVICE POINT
.
<<A>> SNAP RING REMOVAL
1. Set special tools MD999590 and MD998924 as shown in the
illustration.
2. Compress the return spring and remove the snap ring.
ASSEMBLY SERVICE POINTS
.
>>A<< D-RING INSTALLATION
1. Install D-rings in the grooves on the reverse clutch retainer,
piston, overdrive clutch piston and spring retainer. Be careful
not to twist or damage the D-rings.
2. Apply ATF or petroleum jelly (Vaseline) to D-rings.
.
>>B<< REVERSE CLUTCH PISTON INSTALLATION
Align the outer circumference holes ("A" and "B") of the reverse
clutch piston and the reverse clutch retainer to assemble them.
.
>>C<< SNAP RING INSTALLATION
1. Set special tools MD999590 and MD998924 as shown in the
illustration.
2. Tighten the nut on the special tool to press down on the
spring retainer and reverse clutch retainer, and then install
the snap ring.
3. Check that the clearance between the snap ring and the
return spring retainer is within the standard value. If not
within the standard value, select a snap ring so that it is.
Standard value: 0
− 0.09 mm (0 − 0.0035 inch)
.
AKX01046
MD998924
MD999590
AB
AK101754
D-RING
REVERSE CLUTCH RETAINER
REVERSE CLUTCH PISTON
OVERDRIVE CLUTCH PISTON
SPRING RETAINER
AB
AKX01048
HOLE "A"
HOLE "B"
AB
AKX01046
MD998924
MD999590
AB
REVERSE AND OVERDRIVE CLUTCH
TSB Revision
AUTOMATIC TRANSAXLE OVERHAUL
23B-62
>>D<< PRESSURE PLATE/CLUTCH PLATE/CLUTCH
DISC/CLUTCH REACTION PLATE INSTALLATION
1. Install the pressure plate in the direction shown <F4A51>.
CAUTION
Immerse the clutch disc in ATF before assembling it. IF the
clutch disc is new, soak it in ATF for more than two hours.
2. Assemble the clutch discs and clutch plates, one on top of
the other, inside the reverse clutch piston.
NUMBER OF CLUTCH DISCS AND PLATES
3. Install the clutch reaction plate in the direction shown.
.
>>E<< SNAP RING INSTALLATION
1. Install the snap ring into the groove in the reverse clutch
piston.
2. Set special tools MB991628 <F4A42>, MB991629 <F4A51>
and MD998924 as shown in the illustration, and compress
the clutch element.
3. Check that the clearance between the snap ring and the
clutch reaction plate is within the standard value. If not within
the standard value, select a snap ring so that it is.
Standard value: 1.6
− 18 mm (0.0630 − 0.0709 inch)
.
MODEL
PRESSURE
PLATE
CLUTCH
DISC
CLUTCH
PLATE
CLUTCH
REACTION
PLATE
F4A42
−
4
4
1
F4A51
1
4
3
1
AKX00956
<F4A42>
CLUTCH PLATES
ROUNDED EDGE
CLUTCH DISCS
CLUTCH DISCS
<F4A51>
CLUTCH
PLATES
ROUNDED EDGE
PRESSURE
PLATE
AB
CLUTCH
REACTION
PLATE
CLUTCH
REACTION
PLATE
AKX01049
MB991628
<F4A42> OR
MB991629
<F4A51>
MD998924
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст