Mitsubishi Eclipse. Manual — part 281
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-617
STEP 5. Using scan tool MB991958, check data list item 24:
Vehicle Speed Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine.
(3) Set scan tool MB991958 to the data reading mode for item
24, Vehicle Speed Sensor.
• Check that the speedometer and MB991958 display
speed match when traveling at a vehicle speed of 40
km/h (25 mph).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
NO : Replace the ECM. Then go to Step 17.
AK300810
AB
MB991911
16-PIN
MB991827
MB991824
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-618
STEP 6. Measure the sensor supply voltage at ECM
connector C-60 by backprobing.
(1) Do not disconnect the ECM connector C-60.
(2) Disconnect the vehicle speed sensor connector B-39.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between terminal No. 86 and ground
by backprobing.
• Voltage should be between 4.8 and 5.2 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.8 and 5.2 volts?
YES : Go to Step 7.
NO : Replace the ECM. Then go to Step 17.
STEP 7. Check connector C-60 at ECM for damage.
Q: Is the connector in good condition?
YES : Check connector B-36 at intermediate connector for
damage, and repair or replace as required. Refer to
GROUP 00E, Harness Connector Inspection
. If intermediate connector is in good
condition, repair harness wire between vehicle speed
sensor connector B-39 (terminal No. 3) and ECM
connector C-60 (terminal No. 86) because of open
circuit. Then go to Step 17.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 17.
AK300415
82
78
8180
89
90
91
92
79
87
71
74 73 72
76 75
77
85
88
83
84
86
CONNECTOR: C-60 <M/T>
AB
C-60 (G)
HARNESS CONNECTOR:
COMPONENT SIDE
AK000304
7172 73 74 75 76 77 78 79 80 81
82 83 84 85 86 87 88 89 90
92
91
AH
C-60 HARNESS
CONNECTOR:
HARNESS SIDE
AK300415
82
78
8180
89
90
91
92
79
87
71
74 73 72
76 75
77
85
88
83
84
86
CONNECTOR: C-60 <M/T>
AB
C-60 (G)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-619
STEP 8. Check connector B-39 at vehicle speed sensor for
damage.
Q: Is the connector in good condition?
YES : Go to Step 9.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 17.
STEP 9. Measure the power supply voltage at vehicle
speed sensor harness side connector B-39.
(1) Disconnect the connector B-39 and measure at the harness
side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal No. 1 and ground.
• Voltage should be battery positive voltage.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is battery positive voltage (approximately 12 volts)
present?
YES : Go to Step 10.
NO : Check connectors B-36, C-28, C-78, C-112 and C-111
at intermediate connector for damage, and repair or
replace as required. Refer to GROUP 00E, Harness
Connector Inspection
. If intermediate
connectors are in good condition, repair harness wire
between ignition switch connector C-87 (terminal No.
2) and vehicle speed sensor connector B-39 (terminal
No. 1) because of open circuit or short circuit to
ground. Then go to Step 17.
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
AKX01425AL
B-39 HARNESS
CONNECTOR:
COMPONENT SIDE
3 2 1
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-620
STEP 10. Check the continuity at vehicle speed sensor
harness side connector B-39.
(1) Disconnect the connector B-39 and measure at the harness
side.
(2) Check for the continuity between terminal No. 2 and
ground.
• Should be less than 2 ohms.
Q: Is the continuity normal?
YES : Go to Step 11.
NO : Check connector B-36 at intermediate connector for
damage, and repair or replace as required. Refer to
GROUP 00E, Harness Connector Inspection
. If intermediate connector is in good
condition, repair harness wire between vehicle speed
sensor connector B-39 (terminal No. 2) and ground
because of open circuit or harness damage. Then go
to Step 17.
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
AKX01426
3 2 1
B-39 HARNESS
CONNECTOR:
COMPONENT SIDE
AV
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст