Mitsubishi Eclipse. Manual — part 282
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-621
STEP 11. Measure the sensor supply voltage at vehicle
speed sensor harness side connector B-39.
(1) Disconnect the vehicle speed sensor connector B-39 and
measure at the harness side.
(2) Disconnect the combination meter connector and
auto-cruise control-ECU connector.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between terminal No. 3 and ground.
• Voltage should be between 4.8 and 5.2 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage between 4.8 and 5.2 volts?
YES : Go to Step 12.
NO : Check connector B-36 at intermediate connector for
damage, and repair or replace as required. Refer to
GROUP 00E, Harness Connector Inspection
. If intermediate connector is in good
condition, repair harness wire between vehicle speed
sensor connector B-39 (terminal No. 3) and ECM
connector C-60 (terminal No. 86) because of short
circuit to ground or harness damage. Then go to Step
17.
STEP 12. Check the vehicle speed sensor.
Refer to GROUP 54A, Combination Metre
− Inspection − Vehi-
cle Speed Sensor Check
Q: Is the vehicle speed sensor normal?
YES : Go to Step 13.
NO : Replace the vehicle speed sensor. Then go to Step
17.
STEP 13. Check connector C-60 at ECM for damage.
Q: Is the connector in good condition?
YES : Go to Step 14.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Then go to Step 17.
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
AKX01427
3 2 1
B-39 HARNESS
CONNECTOR:
COMPONENT SIDE
AU
AK300415
82
78
8180
89
90
91
92
79
87
71
74 73 72
76 75
77
85
88
83
84
86
CONNECTOR: C-60 <M/T>
AB
C-60 (G)
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-622
STEP 14. Check for harness damage between ignition
switch connector C-87 (terminal No. 2) and vehicle speed
sensor connector B-39 (terminal No. 1).
NOTE: Check harness after checking intermediate connectors
B-36, C-28, C-78, B-112 and C-111. If intermediate connectors
are damaged, repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
. Then go to Step 17.
Q: Is the harness wire in good condition?
YES : Go to Step 15.
NO : Repair it. Then go to Step 17.
AK300738
1
2
3
4
5
6
CONNECTOR: C-87
AB
HARNESS CONNECTOR:
COMPONENT SIDE
C-87
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-623
STEP 15. Check for harness damage between vehicle
speed sensor connector B-39 (terminal No. 3) and ECM
connector C-60 (terminal No. 86).
NOTE: Check harness after checking intermediate connector
B-36. If intermediate connector is damaged, repair or replace
them. Refer to GROUP 00E, Harness Connector Inspection
. Then go to Step 17.
Q: Is the harness wire in good condition?
YES : Go to Step 16.
NO : Repair it. Then go to Step 17.
STEP 16. Check for harness damage between vehicle
speed sensor connector B-39 (terminal No. 2) and ground.
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
AK300415
82
78
8180
89
90
91
92
79
87
71
74 73 72
76 75
77
85
88
83
84
86
CONNECTOR: C-60 <M/T>
AB
C-60 (G)
HARNESS CONNECTOR:
COMPONENT SIDE
AK300425
1
2
3
B-39 (B)
AB
CONNECTOR: B-39
HARNESS CONNECTOR:
COMPONENT SIDE
MULTIPORT FUEL INJECTION (MFI) DIAGNOSIS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <2.4L>
13A-624
NOTE: Check harness after checking intermediate connector
B-36. If intermediate connector is damaged, repair or replace
them. Refer to GROUP 00E, Harness Connector Inspection
. Then go to Step 17.
Q: Is the harness wire in good condition?
YES : Check for harness wire between vehicle speed
sensor connector B-39 (terminal No. 3) and other
system because of short circuit to ground. Then go to
Step 17.
NO : Repair it. Then go to Step 17.
STEP 17. Using scan tool MB991958, check data list item
24: Vehicle Speed Sensor.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to "LOCK" (OFF) position before connect-
ing or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Start the engine.
(3) Set scan tool MB991958 to the data reading mode for item
24, Vehicle Speed Sensor.
• Check that the speedometer and MB991958 display
speed match when traveling at a vehicle speed of 40
km/h (25 mph).
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : The inspection is complete.
NO : Retry the troubleshooting.
AK300810
AB
MB991911
16-PIN
MB991827
MB991824
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст