Mitsubishi Eclipse. Manual — part 845
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-389
INSPECTION PROCEDURE USING AN OSCILLOSCOPE
M1231008500283
Waveform sample
TERMINAL
NO.
INSPECTION ITEM
INSPECTION REQUIREMENT
NORMAL
CONDITION
(WAVEFORM
SAMPLE)
45
Crankshaft position
sensor
Selector lever position:
N
Idling (Vehicle stopped)
Waveform A
103
Input shaft speed
sensor
Selector lever position:
3 <Vehicles without
sport mode>, Sport
mode <Vehicles with
sport mode>
Driving at constant speed of
50 km/h (31 mph) in 3rd gear
(2.4L Engine: 1,600
− 1,900
r/min, 3.0L Engine: 1,300
−
1,600 r/min)
Waveform B
104
Output shaft speed
sensor
80
Vehicle speed signal
Waveform C
129
Low-reverse solenoid
valve
• Ignition switch: ON
• Selector lever
position: P
• Engine: Stopped
• Throttle
(Accelerator)
opening angle: Less
than 1 volt
Force drive each solenoid
valve (Actuator test)
Waveform D
120
Underdrive solenoid
valve
106
Second solenoid valve
130
Overdrive solenoid
valve
107
Torque converter clutch
control solenoid
AC001872AE
WAVEFORM A
(V)
0
5
(ms)
AC001873AD
WAVEFORM B
(V)
0
5
(ms)
AC001872AF
WAVEFORM C
(V)
0
12
(ms)
AC001875AD
WAVEFORM D
(V)
0
20
(ms)
40
60
A/T FAULTY OPERATION PREVENTION MECHANISM DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-390
A/T FAULTY OPERATION PREVENTION MECHANISM
DIAGNOSIS
INTRODUCTION TO A/T KEY INTERLOCK AND SHIFT LOCK MECHANISMS
M1232001600237
If the key interlock and shift lock mechanisms indi-
cates a malfunction, the key interlock cable, the shift
lock cable, or the selector lever assembly may be
defective. In this case, follow troubleshooting below.
A/T KEY INTERLOCK AND SHIFT LOCK MECHANISMS DIAGNOSTIC
TROUBLESHOOTING STRATEGY
M1232001700234
Use these steps to plan your diagnostic strategy. If
your follow then carefully, you will be sure that you
have exhausted most of the possible ways to find
automatic transaxle key interlock and shift lock
mechanisms fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by following the Symptom
Chart.
4. Verify malfunction is eliminated.
SYMPTOM CHART
M1232001800424
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE
PAGE
Selector lever can be moved from "P" to "R" position without depressing
brake pedal when ignition key is at any position other than "LOCK" (OFF)
position.
1
Selector lever cannot be moved from "P" to "R" position with brake pedal
depressed when ignition key is at any position other than "LOCK" (OFF)
position.
2
Selector lever can be moved from "P" to "R" position with brake pedal
depressed when ignition key is at "LOCK" (OFF) position.
3
Selector lever cannot be moved from "P" to "R" position smoothly.
4
Selector lever cannot be moved from "P" to "R" position.
5
Ignition key cannot be turned to "LOCK" (OFF) position when selector
lever is at "P" position.
6
Ignition key can be turned to "LOCK" (OFF) position when selector lever
is at any position other than "P" position.
7
A/T FAULTY OPERATION PREVENTION MECHANISM DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-391
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Selector Lever can be Moved from "P" to "R" Position without
Depressing Brake Pedal when Ignition Key is at any Position Other than "LOCK" (OFF) Position.
.
TECHNICAL DESCRIPTION (COMMENT)
Lock cam or shift lock cable may be defective.
.
TROUBLESHOOTING HINTS
• Malfunction of lock cam
• Malfunction of shift lock cable
DIAGNOSIS
STEP 1. Check the fit of the lock cam.
Q: Is the lock cam installed correctly?
YES :
Go to Step 2.
NO :
Install the lock cam correctly. Refer to
. When the brake pedal is
released with the ignition key at other
positions than "LOCK" (OFF) position,
check that the selector lever can not be
moved from "P" position to "R" position.
STEP 2. Check the lock cam.
Q: Is the lock cam in good condition?
YES :
Go to Step 3.
NO :
Replace the lock cam. Refer to
.
When the brake pedal is released with the
ignition key at other positions than "LOCK"
(OFF) position, check that the selector lever
can not be moved from "P" position to "R"
position.
STEP 3. Check the fit of the shift lock cable.
Q: Is the shift lock cable installed correctly?
YES :
Go to Step 4.
NO :
Install the shift lock cable correctly. Refer to
. When the brake pedal is
released with the ignition key at other
positions than "LOCK" (OFF) position,
check that the selector lever can not be
moved from "P" position to "R" position.
STEP 4. Check the shift lock cable.
Q: Is the shift lock cable in good condition?
YES :
No action to be taken.
NO :
Replace the shift lock cable. Refer to
. When the brake pedal is
released with the ignition key at other
positions than "LOCK" (OFF) position,
check that the selector lever can not be
moved from "P" position to "R" position.
INSPECTION PROCEDURE 2: Selector Lever cannot be Moved from "P" to "R" Position with Brake
Pedal Depressed when Ignition Key is at any Position Other than "LOCK" (OFF) Position.
.
TECHNICAL DESCRIPTION (COMMENT)
Selector lever assembly, shift lock cable, key inter-
lock cable, transmission control cable, or lock cam
may be defective.
.
TROUBLESHOOTING HINTS
• Malfunction of selector lever assembly
• Malfunction of shift lock cable
• Malfunction of key interlock cable
• Malfunction of transmission control cable
• Malfunction of lock cam
A/T FAULTY OPERATION PREVENTION MECHANISM DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-392
DIAGNOSIS
STEP 1. Check the connection of lock cam and
key interlock cable.
Q: Is the connection of lock cam and key interlock
cable in good condition?
YES :
Go to Step 2.
NO :
Repair the connection of lock cam and shift
lock cable. When the brake pedal is
depressed with the ignition key at other
positions than "LOCK" (OFF) position,
check that the selector lever can be moved
from "P" position to "R" position.
STEP 2. Check the connection of selector lever
assembly and shift transaxle control cable.
Q: Is the connection of selector lever assembly and
shift transaxle control cable in good condition?
YES :
Go to Step 3.
NO :
Repair the connection of selector lever
assembly and shift transaxle control cable.
When the brake pedal is depressed with the
ignition key at other positions than "LOCK"
(OFF) position, check that the selector lever
can be moved from "P" position to "R"
position.
STEP 3. Check the fit of the shift lock cable.
Q: Is the shift lock cable installed correctly?
YES :
Go to Step 4.
NO :
Install the shift lock cable correctly. Refer to
. When the brake pedal is
depressed with the ignition key at other
positions than "LOCK" (OFF) position,
check that the selector lever can be moved
from "P" position to "R" position.
STEP 4. Check the shift lock cable.
Q: Is the shift lock cable in good condition?
YES :
Go to Step 5.
NO :
Replace the shift lock cable. Refer to
. When the brake pedal is
depressed with the ignition key at other
positions than "LOCK" (OFF) position,
check that the selector lever can be moved
from "P" position to "R" position.
STEP 5. Check the fit of the key interlock cable.
Q: Is the key interlock cable installed correctly?
YES :
Go to Step 6.
NO :
Install the key interlock cable correctly.
Refer to
. When the brake pedal
is depressed with the ignition key at other
positions than "LOCK" (OFF) position,
check that the selector lever can be moved
from "P" position to "R" position.
STEP 6. Check the key interlock cable.
Q: Is the key interlock cable in good condition?
YES :
Go to Step 7.
NO :
Replace the key interlock cable. Refer to
. When the brake pedal is
depressed with the ignition key at other
positions than "LOCK" (OFF) position,
check that the selector lever can be moved
from "P" position to "R" position.
STEP 7. Check the fit of the transaxle control
cable.
Q: Is the transaxle control cable installed correctly?
YES :
Go to Step 8.
NO :
Install the transaxle control cable correctly.
Refer to
. When the brake pedal
is depressed with the ignition key at other
positions than "LOCK" (OFF) position,
check that the selector lever can be moved
from "P" position to "R" position.
STEP 8. Check the transaxle control cable.
Q: Is the transaxle control cable in good condition?
YES :
Repair or replace the selector lever
assembly. Refer to
and
. When the brake pedal is
depressed with the ignition key at other
positions than "LOCK" (OFF) position,
check that the selector lever can be moved
from "P" position to "R" position.
NO :
Replace the transaxle control cable. Refer
to
. When the brake pedal is
depressed with the ignition key at other
positions than "LOCK" (OFF) position,
check that the selector lever can be moved
from "P" position to "R" position.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст