Mitsubishi Eclipse. Manual — part 125
12-1
GROUP 12
ENGINE
LUBRICATION
CONTENTS
GENERAL DESCRIPTION. . . . . . . . .
SPECIAL TOOLS. . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
ENGINE OIL CHECK . . . . . . . . . . . . . . . . .
ENGINE OIL REPLACEMENT . . . . . . . . . .
ENGINE OIL FILTER REPLACEMENT . . .
ENGINE OIL PRESSURE CHECK . . . . . . .
SPECIFICATIONS . . . . . . . . . . . . . . .
FASTENER TIGHTENING
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS . . . . . . . . . . .
SEALANT . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION
TSB Revision
ENGINE LUBRICATION
12-2
GENERAL DESCRIPTION
M1121000100368
The lubrication method is a fully force-fed, full-flow fil-
tration type.
ENGINE OILS
WARNING
Prolonged and repeated contact with mineral oil will result in the removal of natural fats from
the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains
potentially harmful contaminants which may cause skin cancer. Adequate means of skin pro-
tection and washing facilities must be provided.
.
Recommended Precautions:
The most effective precaution is to adapt working
practices which prevent, as far as practical, the risk
of skin contact with mineral oils i.e. use enclosed
systems for handling used engine oil and decrease
components, where practical, before handling them.
.
Other Precautions:
• Avoid prolonged and repeated contact with oil,
particularly used engine oil.
• Wear protective clothing, including impervious
gloves where practical.
• Avoid contaminating clothes, particularly under
wear, with oil.
• Do not put oily rags in pockets.
• Do not wear heavily soiled clothing and
oil-soaked foot-wear. Overalls must be cleaned
regularly and kept separate from personal cloth-
ing.
• Where there is a risk of eye contact, eye protec-
tion should be worn i.e. chemical goggles or face
shields. In addition, an eye wash facility should
be provided.
• Obtain First Aid treatment immediately for open
cuts and wounds.
• Wash regularly with soap and water to ensure all
oil is removed, especially before meals (skin
cleansers and nail brushes will help). After clean-
ing, apply lotion, etc., containing lanolin to
replace natural skin oils is advised.
• Do not use gasoline, kerosene, diesel fuel, gas
oil, thinners or solvents for cleaning skin.
• Apply barrier creams before each work period to
help clean the skin after work.
• If skin disorders develop, obtain medical advice
immediately.
ITEM
2.4L ENGINE
3.0L ENGINE
Oil pump type
Involute gear type
Trochoid type
Drive method
Timing belt
Crankshaft
SPECIAL TOOLS
TSB Revision
ENGINE LUBRICATION
12-3
SPECIAL TOOLS
M1121000600396
ON-VEHICLE SERVICE
ENGINE OIL CHECK
M1121000900193
1. Pull out the oil dipstick slowly and check that the oil level is
within the marks on the oil dipstick.
2. Check that the oil is not excessively dirty, that there is no
coolant or gasoline mixed in, and that it is sufficiently thick
and slippery.
ENGINE OIL REPLACEMENT
M1121001000405
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
°C (176°F) to 90°C
(194
°F).
2. Remove the engine oil filler cap.
WARNING
Use care as oil could be hot.
3. Remove the drain plug to drain oil.
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION
APPLICATION
MB991396
Oil filter wrench
Tool not available
Removal and installation of
engine oil filter (when using
the oil filter of MD360935,
MD325714, MD332687 and
MD365876) <2.4L Engine>
MD998054
Engine oil pressure
switch wrench
Tool not available
Removal and installation of
engine oil pressure switch
B991396
ACX00892AB
GOOD
MAXIMUM
MINIMUM
ON-VEHICLE SERVICE
TSB Revision
ENGINE LUBRICATION
12-4
4. Install a new drain plug gasket so that it faces in the
direction shown in the illustration, and then tighten the drain
plug to the specified torque.
Tightening torque: 39
± 5 N⋅m (29 ± 4 ft-lb)
5. Refill the specified quantity of oil.
Specified Engine Oil: Engine oil displaying ILSAC cer-
tification mark ("Starburst" symbol) conforming the
API classification SJ EC or SJ/CD EC
Total quantity (Includes volume inside oil filter): 4.3
dm
3
(4.5 quarts)
6. Install the engine oil filler cap.
7. Check oil level.
ENGINE OIL FILTER REPLACEMENT
M1121001100372
Required Special Tool:
• MB991396 (When using the oil filter of MD360935,
MD325717, MD332687 and MD365876): Oil Filter Wrench
1. Start the engine and allow it to warm up until the
temperature of the coolant reaches 80
°C (176°F) to 90°C
(194
°F).
2. Remove the engine oil filler cap.
WARNING
Use care as oil could be hot.
3. Remove the drain plug to drain oil.
AC000092
<2.4L ENGINE>
DRAIN PLUG GASKET
OIL
PAN
SIDE
DRAIN
PLUG
39 ± 5 N·m
29 ± 4 ft-lb
39 ± 5 N·m
29 ± 4 ft-lb
DRAIN
PLUG
OIL
PAN
SIDE
DRAIN PLUG GASKET
<3.0L ENGINE>
AB
ACX00887AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст