Mitsubishi Eclipse. Manual — part 644
SPECIFICATIONS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-1119
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATION
M1131011600465
GENERAL SPECIFICATIONS
M1131000200515
ITEM
SPECIFICATION
Dashpot
3.4
± 1.0 N⋅m (30 ± 9 in-lb)
Engine coolant temperature sensor
29
± 10 N⋅m (22 ± 7 ft-lb)
Fuel high-pressure hose
4.9
± 1.0 N⋅m (44 ± 8 in-lb)
Fuel rail mounting bolt
12
± 1 N⋅m (100 ± 13 in-lb)
Fuel pressure regulator
8.8
± 1.0 N⋅m (78 ± 9 in-lb)
Idle air control motor
2.0
± 0.5 N⋅m (18 ± 4 in-lb)
Lever assembly
4.9
± 1.0 N⋅m (43 ± 9 in-lb)
Throttle body bracket M6
4.9
± 1.0 N⋅m (44 ± 8 in-lb)
Throttle body bracket M8
6.9
± 1.5 N⋅m (61 ± 13 in-lb)
Throttle body to intake manifold bolt
19
± 3 N⋅m (14 ± 2 ft-lb)
Throttle position sensor
2.0
± 0.5 N⋅m (18 ± 4 in-lb)
Throttle speed adjusting screw mounting bolt
2.0
± 0.5 N⋅m (18 ± 4 in-lb)
ITEMS
SPECIFICATIONS
Throttle body
Throttle bore mm (in.)
60 (2.4)
Throttle position sensor
Variable resistor type
Idle air control motor
Stepper motor (stepper motor type by-pass air
control system with the air volume limiter)
Engine control
module (ECM)
<M/T>
Identification model No.
E6T35971 <Eclipse and Eclipse spyder without
variable induction system>
E6T35972 <Eclipse-with variable induction system>
E6T35973 <Eclipse spyder-with variable induction
system>
Powertrain
control module
(PCM) <A/T>
Identification model No.
E6T34184 <Eclipse and Eclipse spyder without
variable induction system>
E6T34187 <Eclipse-with variable induction system>
E6T34186 <Eclipse spyder-with variable induction
system>
SPECIFICATIONS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-1120
SERVICE SPECIFICATIONS
M1131000300619
Sensors
Volume airflow sensor
Karman vortex type
Barometric pressure sensor
Semiconductor type
Intake air temperature sensor
Thermistor type
Engine coolant temperature sensor
Thermistor type
Heated oxygen sensor
Zirconia type
Vehicle speed sensor <M/T>
Electromagnetic resistance element type
Transmission range switch <A/T>
Contact switch type
Camshaft position sensor
Electromagnetic resistance element type
Crankshaft position sensor
Hall element type
Knock sensor
Piezoelectric type
Power steering pressure switch
Contact switch type
Manifold absolute pressure sensor
Semiconductor type
Actuators
Multiport fuel injection (MFI) relay
Contact switch type
Fuel pump relay
Contact switch type
Injector type and number
Electromagnetic type, 6
Injector identification mark
CDH210
EGR vacuum regulator solenoid valve Duty cycle type solenoid valve
Evaporative emission purge solenoid Duty cycle type solenoid valve
Fuel pressure
regulator
Regulator pressure kPa (in.Hg)
335 (98)
ITEMS
SPECIFICATIONS
ITEMS
STANDARD VALUE
Throttle position sensor adjusting voltage mV
535
− 735
Basic idle speed r/min
700
± 50
Fuel pressure kPa (psi)
Vacuum hose disconnected 330
− 350 (47 − 50) at curb idle
Vacuum hose connected
Approximately 270 (38) at curb idle
Intake air temperature sensor resistance
k
Ω
-20
°C (-4°F)
13
− 17
0
°C (32°F)
5.3
− 6.7
20
°C (86°F)
2.3
− 3.0
40
°C (104°F)
1.0
− 1.5
60
°C (140°F)
0.56
− 0.76
80
°C (176°F)
0.30
− 0.42
Engine coolant temperature sensor
resistance k
Ω
-20
°C (-4°F)
14
− 17
0
°C (32°F)
5.1
− 6.5
20
°C (68°F)
2.1
− 2.7
40
°C (104°F)
0.9
− 1.3
60
°C (140°F)
0.48
− 0.68
80
°C (176°F)
0.26
− 0.36
Throttle position sensor resistance k
Ω
3.5
− 6.5
Heated oxygen sensor output voltage V
0.6
− 1.0
SPECIFICATIONS
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-1121
SEALANT AND ADHESIVE
M1131000500378
Heated oxygen sensor heater resistance
Ω
Front
4.5
− 8.0
Rear
11
− 18
Injector coil resistance
Ω
13
− 16 [at 20°C (68°F)]
Idle air control motor coil resistance
Ω
28
− 33 [at 20°C (68°F)]
ITEMS
STANDARD VALUE
ITEM
SPECIFIED SEALANT
Engine coolant temperature sensor threaded portion 3M
AAD part number 8731or equivalent
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст