Mitsubishi Eclipse. Manual — part 643
INJECTOR
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-1115
INSTALLATION SERVICE POINT
.
>>A<< INJECTORS/FUEL PRESSURE REGULATOR/FUEL
HIGH-PRESSURE HOSE INSTALLATION
CAUTION
Do not allow the engine oil to enter the fuel rail, otherwise
it will be damaged.
1. Apply a drop of new engine oil to the O-ring.
2. Turn the injector. To the right and left to install to the fuel rail.
Repeat for fuel pressure regulator and fuel high-pressure
hose. Be careful not to damage the O-ring. After installing,
check that the item turns smoothly.
3. If it dose not turn smoothly, the O-ring may be trapped,
remove the item, re-install it into the fuel rail and check
again.
4. Tighten the fuel pressure regulator and fuel high-pressure
hose to the specified torque.
Tightening torque:
8.8
± 1.0 N⋅m (78 ± 9 in-lb) <Fuel pressure regulator>
4.9
± 1.0 N⋅m (44 ± 8 in-lb) <Fuel high-pressure hose>
THROTTLE BODY ASSEMBLY
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-1116
THROTTLE BODY ASSEMBLY
REMOVAL AND INSTALLATION
M1131007700317
Pre-removal Operation
• Engine Coolant Draining [Refer to GROUP 00, Mainte-
nance Service
− Engine Coolant (Change)
• Air Cleaner Removal (Refer to GROUP 15, Air Cleaner
.)
Post-installation Operation
• Air Cleaner Installation (Refer to GROUP 15, Air Cleaner
.)
• Engine Coolant Refilling [Refer to GROUP 00, Mainte-
nance Service
− Engine Coolant (Change)
• Accelerator Cable Adjustment (Refer to GROUP 17,
On-vehicle Service
− Accelerator Cable Check and
Adjustment
AC001624
4
6
4
4
7
2
1
4
3
5
8
19 ± 3 N·m
14 ± 2 ft-lb
AB
N
5
REMOVAL STEPS
1.
ACCELERATOR CABLE
CONNECTION
2.
THROTTLE POSITION SENSOR
CONNECTOR
3.
IDLE AIR CONTROL MOTOR
CONNECTOR
4.
VACUUM HOSE CONNECTION
5.
WATER HOSE CONNECTION
6.
VACUUM PIPE CONNECTION
7.
THROTTLE BODY
>>A<<
8.
THROTTLE BODY GASKET
REMOVAL STEPS (Continued)
THROTTLE BODY ASSEMBLY
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-1117
INSTALLATION SERVICE POINT
.
>>A<< THROTTLE BODY GASKET INSTALLATION
CAUTION
Poor idling etc. may result if the throttle body gasket is
installed incorrectly.
Install the throttle body gasket as shown in the illustration.
DISASSEMBLY AND ASSEMBLY
M1131009700197
NOTE: IF THE ADJUSTING SCREW WAS HAPPEN
TO HAVE BEEN REMOVED, PERFORM SPEED
ADJUSTING SCREW ADJUSTMENT.
AC000233
PROJECTION
AB
AK101761
7
6
5
8
9
2
1
4
3
4.9 ± 1 N·m
43 ± 9 in-lb
4.9 ± 1 N·m
43 ± 9 in-lb
6.9 ± 1.5 N·m
61 ± 13 in-lb
2.0 ± 0.5 N·m
18 ± 4 in-lb
4.9 ± 1 N·m
43 ± 9 in-lb
2.0 ± 0.5 N·m
18 ± 4 in-lb
2.0 ± 0.5 N·m
18 ± 4 in-lb
AB
REMOVAL STEPS
<<A>> >>A<<
1. THROTTLE POSITION SENSOR
2. LEVER ASSEMBLY
3. IDLE AIR CONTROL MOTOR
4. O-RING
<<B>>
5. THROTTLE BODY
6. THROTTLE SPEED ADJUSTING
SCREW
7. BRACKET
8. SPEED ADJUSTING SCREW
9. O-RING
REMOVAL STEPS (Continued)
THROTTLE BODY ASSEMBLY
TSB Revision
MULTIPORT FUEL INJECTION (MFI) <3.0L>
13B-1118
DISASSEMBLY SERVICE POINTS
.
<<A>> THROTTLE POSITION SENSOR DISASSEMBLY
1. Do not disassemble the sensor and motor.
2. Do not clean the sensor and motor by dipping them into
cleaning solvent. Clean them with shop towel.
.
<<B>> THROTTLE BODY DISASSEMBLY
1. Do not disassemble the throttle body.
2. Check if the vacuum port or passage is clogged. Use
compressed air to clean the vacuum passage.
ASSEMBLY SERVICE POINT
.
>>A<< THROTTLE POSITION SENSOR (TPS) INSTALLA-
TION
1. Install the throttle position sensor to the throttle body as
shown in the illustration.
2. Turn the throttle position sensor 90 degrees
counterclockwise to set it, and tighten the screws.
3. Connect an ohmmeter between terminals 1 (ground) and 3
(output), or between terminals 3 (output) and 4 (power).
Then, make sure that the resistance changes smoothly
when the throttle valve is slowly moved to the fully open
position.
AK000037
TPS
AB
1 2 3 4
AK000038AB
AKX01635
THROTTLE POSITION
SENSOR POWER
GROUND
THROTTLE POSITION
SENSOR OUTPUT
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст