Mitsubishi Eclipse. Manual — part 896
FRONT AXLE DIAGNOSIS
TSB Revision
FRONT AXLE
26-3
SYMPTOM CHART
M1261005700195
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Noise during Wheel Rotation
DIAGNOSIS
STEP 1. Check the driveshaft and inner shaft for
bending.
Q: Is the driveshaft and inner shaft bent?
YES :
Replace the part. Then go to Step 4.
NO :
Go to step 2.
STEP 2. Check the inner shaft bearing for wear.
Q: Is the inner shaft bearing worn?
YES :
Replace the bearings. Then go to Step 4.
NO :
Go to Step 3.
STEP 3. Check the driveshaft assembly for wear,
damage or bending.
Q: Is the driveshaft assembly worn, damaged or bent?
YES :
Replace the driveshaft assembly. Then go
to Step 4.
NO :
There is no action to be taken.
STEP 4. Check symptoms.
Q: Is the abnormal noise eliminated?
YES :
This diagnosis is complete.
NO :
Repeat to Step 1.
INSPECTION PROCEDURE 2: Noise due to Excessive Play of Wheel in Turning Direction
DIAGNOSIS
STEP 1. Check for play in the inner shaft and side
gear serration, the driveshaft and side gear, or
the driveshaft and drive flange.
Q: Is the play found?
YES :
Adjust or replace the part. Then go to Step
NO :
This diagnosis is complete.
STEP 2. Check symptoms.
Q: Is the abnormal noise eliminated?
YES :
This diagnosis is complete.
NO :
Repeat to Step 1.
SYMPTOM
INSPECTION
PROCEDURE
REFERENCE PAGE
Driveshaft,
inner shaft
Noise during wheel rotation
1
Noise due to excessive play of wheel in turning
direction
2
SPECIAL TOOLS
TSB Revision
FRONT AXLE
26-4
SPECIAL TOOLS
M1261000600223
TOOL
TOOL NUMBER
AND NAME
SUPERSESSION APPLICATION
MB990767
End yoke holder
MB990767-01
Hub fixing
MB991618
Hub bolt remover
General service
tool
Driving out of hub bolt
MB991897
Ball joint remover
MB991113-01,
MB990635-01 or
General service
tool
Knuckle and tie rod end ball joint
disconnection
NOTE: Steering linkage puller
(MB990635 or MB991113) is also
used to disconnect knuckle and tie rod
end ball joint.
MB990998
Front hub remover
and installer
MB990998-01 or
General service
tool
• Removal of or pressing-in the hub
• Provisional holding of the wheel
bearing
MB990326
Preload socket
General service
tool
Wheel bearing breakaway torque
measurement
MB990241
Axle shaft puller
A: MB990244
Puller shaft
B: MB990242
Puller bar
MB990241-01 or
General service
tool
Drive shaft removal
MB991354
Puller body
MB990241-01 or
General service
tool
Drive shaft removal
B990767
MB991618
AC106827
MB990998
MB990326
MB990241AB
A
B
MB991354
SPECIAL TOOLS
TSB Revision
FRONT AXLE
26-5
MB991248 or
MB998801
Inner shaft
remover
MD998348-01
Inner shaft removal
MB990925
Bearing and oil
seal installer set
MB990925-01 or
General service
tool
Bearing removal and dust seal
installation
MB990890
Rear suspension
bush base
MB990890-01
Oil seal installation
MB991561
Boot band
crimping tool
MB991561
Resin boot band installation
TOOL
TOOL NUMBER
AND NAME
SUPERSESSION APPLICATION
MB991248
MB990925
MB990890
MB991561
TOOL
TYPE
TOOL NUMBER
O D mm (in)
A
MB990926
39.0 (1.54)
MB990927
45.0 (1.77)
MB990928
49.5 (1.95)
MB990929
51.0 (2.00)
MB990930
54.0 (2.13)
MB990931
57.0 (2.24)
MB990932
61.0 (2.40)
MB990933
63.5 (2.50)
MB990934
67.5 (2.66)
MB990935
71.5 (2.81)
MB990936
75.5 (2.97)
MB990937
79.0 (3.11)
B
MB990938
−
C
MB990939
−
ACX02372
A
B
C
BRASS BAR
BAR (SNAP-IN TYPE)
TOOL BOX
MB990925
AB
INSTALL ADAPTER
ON-VEHICLE SERVICE
TSB Revision
FRONT AXLE
26-6
ON-VEHICLE SERVICE
HUB END PLAY CHECK
M1261000900149
1. Remove the disc brake caliper and suspend it with a wire.
2. Remove the brake disc from the front hub.
3. Attach a dial gauge as shown in the illustration, and then
measure the end play while moving the hub in the axial
direction.
Limit: 0.05 mm (0.002 inch)
4. If end play exceeds the limit, replace the front hub assembly.
HUB BOLT REPLACEMENT
M1261001000183
Required Special Tools:
• MB990767: End Yoke Holder
• MB991618: Hub Bolt Remover
1. Remove the caliper assembly and suspend it with wire so
that it does not fall.
2. Remove the brake disc.
3. Use the special tools MB990767 and MB991618 to remove
the hub bolts.
4. Install the plain washer to the new hub bolt, and install the
bolt with a nut.
AC001146
AC001147
MB990767
AB
MB991618
AC001148
MB990767
AB
PLAIN
WASHER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст