Mitsubishi Eclipse. Manual — part 894
CLUTCH
TSB Revision
CLUTCH OVERHAUL
21B-7
CLUTCH DISC
CAUTION
Don't clean the clutch disc in a cleaning solvent.
1. Check the facing for loose rivets, uneven contact, evidence
of seizure, or deposited oils and greases. If defective,
replace the clutch disc.
2. Measure the rivet sink and replace the clutch disc if it is
below the limit.
Minimum limit: 0.3 mm (0.012 inch)
3. Check the torsion spring for play and damage. If defective,
replace the clutch disc.
4. Combine the clutch disc with the input shaft and check for
sliding condition and play in the rotating direction. If poor
sliding condition is evident, clean, reassemble, and recheck.
If excessive play is evident, replace the clutch disc and/or
input shaft.
.
CLUTCH RELEASE BEARING
CAUTION
Release bearing is packed with grease. Therefore, do not
wash it in a cleaning solvent.
1. Check for seizure, damage, noise or improper rotation.
2. Check for wear on the surface which contacts with the
diaphragm spring.
3. Check for wear on the surface which contacts with the
release fork. If abnormally worn, replace.
.
RELEASE FORK
If the surface which contacts with the bearing is abnormally
worn, replace.
.
RELEASE FORK SHAFT <3.0L ENGINE>
Check the release fork shaft for bend and wear, and replace if
necessary.
AKX00764
RIVET SINK
TORSION
SPRING
AB
CLUTCH RELEASE CYLINDER
TSB Revision
CLUTCH OVERHAUL
21B-8
CLUTCH RELEASE CYLINDER
DISASSEMBLY AND REASSEMBLY
M1212001500045
<2.4L ENGINE>
AKX00760
2
5
4
1
6
9
7
8
17 ± 2 N·m
12 ± 1 ft-lb
AB
3
DISASSEMBLY STEPS
1.
PUSH ROD
2.
BOOT
<<A>>
>>A<<
3.
PISTON ASSEMBLY
4.
PISTON CUP
5.
PISTON
6.
CONICAL SPRING
7.
CAP
8.
AIR BLEEDER
9.
RELEASE CYLINDER
DISASSEMBLY STEPS
CLUTCH RELEASE CYLINDER
TSB Revision
CLUTCH OVERHAUL
21B-9
<3.0L ENGINE>
AKX00762
7
8
11 ± 2 N·m
8 ± 1 ft-lb
3
2
9
1
6
4
5
AB
DISASSEMBLY STEPS
1.
PUSH ROD
2.
BOOT
<<A>>
>>A<<
3.
PISTON ASSEMBLY
4.
PISTON CUP
5.
PISTON
6.
CONICAL SPRING
7.
CAP
8.
AIR BLEEDER
9.
RELEASE CYLINDER
DISASSEMBLY STEPS
CLUTCH RELEASE CYLINDER
TSB Revision
CLUTCH OVERHAUL
21B-10
DISASSEMBLY SERVICE POINT
.
<<A>> PISTON ASSEMBLY REMOVAL
1. Cover with a shop towel to prevent the piston from popping
out.
CAUTION
Apply compressed air slowly to prevent brake fluid from
splashing.
2. Apply the compressed air into the tube mounting hole to
remove the piston assembly.
ASSEMBLY SERVICE POINT
.
>>A<< PISTON ASSEMBLY INSTALLATION
1. Apply brake fluid SAE J1703 (DOT3) to the piston cup and
inner surface of the release cylinder.
2. Insert the piston assembly into the release cylinder.
CLUTCH RELEASE CYLINDER INSPECTION
M1212001600042
.
PISTON CUP
Check the lip of piston cup for scratch. If it is scratched, check
the inner surface of the release cylinder for scratches.
.
RELEASE CYLINDER
Check the inner surface of the release cylinder for scratches or
abnormal wear, replace if necessary.
AKX00765
AKX00763
AKX00754
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст