Mitsubishi Eclipse. Manual — part 860
TIMING BELT
TSB Revision
ENGINE OVERHAUL <2.4L>
11B-17
6. Abnormal wear of belt sides. Normal wear is indicated if the
sides are sharp as if cut by a knife. Abnormal wear is
indicated if the sides are ragged.
7. Abnormal wear on teeth.
8. Missing tooth.
.
AUTO-TENSIONER
1. Check for oil leaks. If oil leaks are evident, replace the
auto-tensioner.
2. Check the rod end for wear or damage and replace the
auto-tensioner if necessary.
3. Measure the rod protrusion. If it is out of specification,
replace the auto tensioner.
Standard value: 12 mm (0.5 inch)
4. Press the rod with a force of 98 to 196 N (22 to 44 pound)
and measure the movement of the rod.
If the measured value is out of the standard value, replace
the auto-tensioner.
Standard value: 1.0 mm (0.03 inch) or less
AKX00602
ROUNDED EDGE
ABNORMAL WEAR
(RAGGED)
AB
AKX00603
TOOTH
MISSING
RUBBER EXPOSED
AB
AKX00477
12 mm
(0.5 in)
AB
AKX00478
98 TO 196 N (22 TO 44 lb)
MOVEMENT
AB
FUEL AND EMISSION PARTS
TSB Revision
ENGINE OVERHAUL <2.4L>
11B-18
FUEL AND EMISSION PARTS
REMOVAL AND INSTALLATION
M1113002200032
AKX00513
19 ± 3 N·m
14 ± 2 ft-lb
19 ± 3 N·m
14 ± 2 ft-lb
19 ± 3 N·m
14 ± 2 ft-lb
8.8 ± 2 N·m
78 ± 17 in-lb
2
1
1
10
16
7
14
6
15
13
3
5
12
4
8
9
N
N
N
N
N
N
AB
12 ± 1 N·m
104 ± 9 in-lb
11
REMOVAL STEPS
1. HOSE CLIP
2. WATER HOSE
3. THROTTLE BODY STAY
4. THROTTLE BODY
>>C<<
5. THROTTLE BODY GASKET
6. EGR VALVE
7. GASKET
8. INJECTOR AND FUEL RAIL
9. INSULATOR
>>B<<
10. FUEL PRESSURE REGULATOR
11. O-RING
12. INSULATOR
>>A<<
13. INJECTOR
14. O-RING
15. GROMMET
16. FUEL RAIL
REMOVAL STEPS (Continued)
FUEL AND EMISSION PARTS
TSB Revision
ENGINE OVERHAUL <2.4L>
11B-19
INSTALLATION SERVICE POINTS
.
>>A<< INJECTORS INSTALLATION
CAUTION
Use care not to let engine oil enter the fuel rail.
1. Apply clean engine oil to the O-ring.
2. Insert the injector into the fuel rail.
3. Make sure the injector rotates smoothly.
If not, remove the injector to check the O-ring for damage,
and replace the O-ring if necessary. Then, reinstall the
injector and check that it rotates smoothly.
.
>>B<< FUEL PRESSURE REGULATOR INSTALLATION
CAUTION
Do not let engine oil enter the fuel rail.
1. Apply clean engine oil to the O-ring.
2. Insert the fuel pressure regulator into the fuel rail.
3. Make sure the pressure regulator rotates smoothly.
If not, remove the fuel pressure regulator to check the O-ring
for damage, and replace the O-ring if necessary. Then,
reinstall the fuel pressure regulator and check that it rotates
smoothly.
4. Tighten the two bolts to the specified torque.
Tightening torque: 8.8
± 2 N⋅m (78 ± 17 in-lb)
.
AKX00446
GROMMET
O-RING
AB
FUEL AND EMISSION PARTS
TSB Revision
ENGINE OVERHAUL <2.4L>
11B-20
>>C<< THROTTLE BODY GASKET INSTALLATION
Install a new gasket so that the tab is positioned as shown in
the illustration.
AK000270
GASKET SURFACE OF INTAKE MANIFOLD
TAB
THROTTLE
BODY
GASKET
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст