Mitsubishi Eclipse. Manual — part 903
ON-VEHICLE SERVICE
TSB Revision
REAR AXLE
27-5
3. Pull the hub bolt out using special tools MB990767 and
MB991618.
NOTE: For vehicles with drum brakes, the hub bolts should
be removed near the retainer spring installation position in
order to maintain enough clearance for removal.
4. Install the plain washer to the new hub bolt, and install the
bolt with a nut.
AC001182
MB990767
AB
MB991618
AC001183
MB990767
AB
PLAIN
WASHER
REAR AXLE HUB ASSEMBLY
TSB Revision
REAR AXLE
27-6
REAR AXLE HUB ASSEMBLY
REMOVAL AND INSTALLATION
M1271002000154
CAUTION
The rear hub unit bearing should not be dismantled.
Required Special Tool:
• MB991248: Inner Shaft Remover
AC000977
9
2
3
<VEHICLES WITH REAR DRUM BRAKE>
<VEHICLES WITH REAR DISC BRAKE>
71 ± 7 N·m
53 ± 5 ft-lb
71 ± 7 N·m
53 ± 5 ft-lb
55 ± 5 N·m
41 ± 3 ft-lb
60 ± 5 N·m
45 ± 3 ft-lb
1
8
7
5
1
8
7
6
4
2
AF
9
N
N
REMOVAL STEPS
1.
REAR WHEEL SPEED SENSOR
<VEHICLES WITH ABS> (REFER
TO GROUP 35B, WHEEL SPEED
SENSOR
2.
O-RING
<<A>>
3.
CALIPER ASSEMBLY
4.
BRAKE DRUM
5.
BRAKE DISC
6.
BRAKE HOSE INSTALLATION
BRACKET
7.
REAR HUB ASSEMBLY
<<B>> >>A<<
8.
ABS ROTOR <VEHICLES WITH
ABS>
<<C>>
9.
BACKING PLATE
REMOVAL STEPS (Continued)
REAR AXLE HUB ASSEMBLY
TSB Revision
REAR AXLE
27-7
REMOVAL SERVICE POINTS
.
<<A>> CALIPER ASSEMBLY REMOVAL
Remove the caliper assembly and suspend it with a wire.
.
<<B>> ABS ROTOR REMOVAL
Use special tool MB991248 to remove the ABS rotor.
.
<<C>> BACKING PLATE REMOVAL
Remove the backing plate and suspend it.
INSTALLATION SERVICE POINT
.
>>A<< ABS ROTOR INSTALLATION
Install the ABS rotor as shown in the illustration.
INSPECTION
M1271002100139
• Check the oil seal for crack or damage.
• Check the ABS rotor for chipped teeth.
AC001185
SOCKET
AB
MB991248
AC001186 AB
ABS ROTOR
SOCKET
KNUCKLE
TSB Revision
REAR AXLE
27-8
KNUCKLE
REMOVAL AND INSTALLATION
M1271003000209
CAUTION
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in the unladen condition.
Required Special Tool:
• MB991113 or MB990635: Steering Linkage Puller
Pre-removal Operation
Rear Axle Hub Assembly Removal (Refer to
Post-installation Operation
• Check the Dust Cover for Cracks or Damage by Pushing
it with Finger.
• Rear Axle Hub Assembly Installation (Refer to
AC001187
128 ± 9 N·m*
94 ± 7 ft-lb*
29 ± 4 N·m
21 ± 4 ft-lb
108 ± 10 N·m*
80 ± 7 ft-lb*
98 ± 10 N·m*
73 ± 7 ft-lb*
1
7
6
5
4
3
2
AB
98 ± 10 N·m
73 ± 7 ft-lb
REMOVAL STEPS
1.
TRAILING ARM CONNECTION
2.
LOWER ARM CONNECTION
<<A>>
3.
TOE CONTROL ARM
CONNECTION
4.
SHOCK ABSORBER
CONNECTION
5.
UPPER ARM CONNECTION
6.
HUB CAP
7.
KNUCKLE
REMOVAL STEPS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст