Mitsubishi Eclipse. Manual — part 688
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-33
DTC 15 : Auto-cruise Control Switch System
.
AC106581
Auto-cruise Control Switch System Circuit
AB
AC001451
CONNECTOR: C-20
AB
AC106551AB
CONNECTORS: C-82, C-84, C-96
C-96
C-84
C-82
CLOCK SPRING
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-34
CIRCUIT OPERATION
This circuit judges the signals of each switch ("OFF,"
"SET," "RESUME," "CANCEL" and "MAIN") of the
auto-cruise control switch. The auto-cruise con-
trol-ECU detects the state of the auto-cruise control
switch by sensing the voltages shown below.
• When all switches are OFF, the ECU detects 3.5
− 5.0 volts.
• When the "SET" switch is ON, the ECU detects
0.4
− 2.3 volts.
• When the "RESUME" switch is ON, the ECU
detects 2.3
− 3.5 volts.
• When the "CANCEL" switch is ON, the ECU
detects 0.4 volts or less.
• When the main switch is ON, the ECU detects 7.0
volts.
.
DTC SET CONDITIONS
This code is output when the auto-cruise control
switch "RESUME" switch, "SET" switch or "CAN-
CEL" switch stays ON.
.
TROUBLESHOOTING HINTS
The most likely causes for this code to be set are:
• Malfunction of the auto-cruise control switch.
• Malfunction of the clock spring.
• Damaged harness or connector.
• Malfunction of the auto-cruise control-ECU.
DIAGNOSIS
Required Special Tool:
• MB991223: Harness Set
STEP 1. Check the 12-Volt supply circuit voltage at
auto-cruise control switch connector C-82 (terminal
number 1).
(1) Disconnect auto-cruise control switch connector C-82 and
measure at the harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 1 and ground.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage approximately battery positive voltage?
YES : Go to Step 6.
NO : Go to Step 2.
STEP 2. Check auto-cruise control switch connector C-82.
Q: Is the connector damaged?
YES : Repair or replace connector. Refer to GROUP 00E,
Harness Connector Inspection
. Then check
that diagnostic trouble code 15 is not output.
NO : Go to Step 3.
1
2
3
ACX02255AE
AUTO-CRUISE
CONTROL SWITCH
CONNECTOR: C-82
AC106551AC
CONNECTORS: C-82
CLOCK SPRING
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-35
STEP 3. Check the clock spring.
Refer to GROUP 52B, Air Bag Modules and Clock Spring
.
Q: Is the clock spring damaged?
YES : Replace the clock spring. Refer to GROUP 52B, Air
Bag Modules and Clock Spring
. Then
check that diagnostic trouble code 15 is not output.
NO : Go to Step 4.
STEP 4. Check clock spring connector C-84.
Q: Is any connector damaged?
YES : Repair or replace connector. Refer to GROUP 00E,
Harness Connector Inspection
. Then check
that diagnostic trouble code 15 is not output.
NO : Go to Step 5.
STEP 5. Check clock spring connector C-96.
Q: Is any connector damaged?
YES : Repair or replace connector. Refer to GROUP 00E,
Harness Connector Inspection
. Then check
that diagnostic trouble code 15 is not output.
NO : Check the harness wire between multi-purpose fuse
No.21 and auto-cruise control switch connector C-82
for open circuit or damage. Then repair if necessary.
Then check that diagnostic trouble code 15 is not
output.
AC106551AD
CONNECTORS: C-84
CLOCK SPRING
AC106551AE
CONNECTORS: C-96
CLOCK SPRING
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-36
STEP 6. Check the output circuit voltage at auto-cruise
control switch connector C-82 (terminal numbers 2 and 3)
by backprobing.
(1) Do not disconnect auto-cruise control switch connector
C-207.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 2 and ground by
backprobing.
• Voltage should be battery positive voltage. (MAIN switch
is at the "ON" position.)
(4) Measure the voltage between terminal 3 and ground by
backprobing.
• Voltage should be between 6.8 and 7.2 volts. (MAIN
switch is at the "ON" position.)
• Voltage should be between 3.5 and 5.0 volts. (All
switches are at the "OFF" position.)
• Voltage should be between 0.4 and 2.3 volts. ("SET"
switch is at the "ON" position)
• Voltage should be between 2.3 and 3.5 volts.
("RESUME" switch is at the "ON" position.)
• Voltage should be between 1 volt or less. ("CANCEL"
switch is at the "ON" position.)
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage within specifications?
YES : Go to Step 9.
NO : Go to Step 7.
STEP 7. Check auto-cruise control switch connector C-82.
Q: Is the connector damaged?
YES : Repair or replace connector. Refer to GROUP 00E,
Harness Connector Inspection
. Then check
that diagnostic trouble code 15 is not output.
NO : Go to Step 8.
1 2
3
ACX01913 AE
C-82 CONNECTOR
HARNESS SIDE VIEW
AC106551AC
CONNECTORS: C-82
CLOCK SPRING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст