Mitsubishi Eclipse. Manual — part 689
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-37
STEP 8. Check the auto-cruise control switch.
(1) Disconnect auto-cruise control switch. (Refer to
.)
(2) Measure the resistance between the terminals when each
of the "SET," "RESUME," "CANCEL" and MAIN switch is
pressed.
Q: Is the values measured correspond to those in the table
below?
YES : Check that diagnostic trouble code 15 is not output. If
diagnostic trouble code 15 is output, replace the
auto-cruise control-ECU (Refer to
.). Then
check that diagnostic trouble code 15 is not output.
NO : Replace the auto-cruise control switch. (Refer to
.). Then check that diagnostic trouble code 15
is not output.
SWITCH
POSITION
TERMINAL
CONNECTOR
OF TESTER
SPECIFIED
CONDITION
"MAIN" switch
"OFF"
1
− 2
Open circuit
"MAIN" switch "ON" 1
− 2
Approximately 3.9 k
Ω
"CANCEL" switch
"ON"
2
− 3
Less than 2 ohms
"RESUME" switch
"ON"
2
− 3
Approximately 910
Ω
"SET" switch "ON"
2
− 3
Approximately 220
Ω
ACX01178 AB
OFF
OFF
OFF
OFF
ON
ON
ON
ON
CAN
MAIN
RES
SET
1
2
3
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-38
STEP 9. Check the output circuit voltage at auto-cruise
control-ECU connector C-20 (terminal numbers 9 and 12)
by backprobing.
(1) Do not disconnect auto-cruise control-ECU connector C-20.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between terminal 12 and ground by
backprobing.
• Voltage should be battery positive voltage. (The MAIN
switch is at the "ON" position.)
(4) Measure the voltage between terminal 9 and ground by
backprobing.
• Voltage should be between 6.8 and 7.2 volts. (MAIN
switch is at the "ON" position.)
• Voltage should be between 3.5 and 5.0 volts. (All
switches are at the "OFF" position.)
• Voltage should be between 0.4 and 2.3 volts. ("SET"
switch is at the "ON" position.)
• Voltage should be between 2.3 and 3.5 volts.
("RESUME" switch is at the "ON" position.)
• Voltage should be between 1 volt or less. ("CANCEL"
switch is at the "ON" position.)
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the voltage within specifications?
YES : Check that diagnostic trouble code 15 is not output. If
diagnostic trouble code 15 is output, replace the
auto-cruise control-ECU (Refer to
.). Then
check that diagnostic trouble code 15 is not output.
NO : Go to Step 10.
STEP 10. Check auto-cruise control-ECU connector C-20.
Q: Is the connector damaged?
YES : Repair or replace connector. Refer to GROUP 00E,
Harness Connector Inspection
. Then check
that diagnostic trouble code 15 is not output.
NO : Go to Step 11.
STEP 11. Check the clock spring.
Refer to GROUP 52B, Air Bag Modules and Clock Spring
.
Q: Is the clock spring damaged?
YES : Replace the clock spring. Refer to GROUP 52B, Air
Bag Modules and Clock Spring
. Then
check that diagnostic trouble code 15 is not output.
NO : Go to Step 12.
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
AC103149AB
C-20 CONNECTOR
HARNESS SIDE VIEW
AC001451
CONNECTOR: C-20
AB
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-39
STEP 12. Check auto-cruise control switch connector
C-82, clock spring connector C-84 and C-96.
Q: Is any connector damaged?
YES : Repair or replace connector. Refer to GROUP 00E,
Harness Connector Inspection
. Then check
that diagnostic trouble code 15 is not output.
NO : Go to Step 13.
STEP 13. Check the harness wire between auto-cruise
control switch connector C-82 (terminal numbers 2 and 3)
and auto-cruise control-ECU connector C-20 (terminal
numbers 9 and 12).
Q: Is any harness wire between auto-cruise control switch
connector C-82 (terminal numbers 2 and 3) and
auto-cruise control-ECU connector C-20 (terminal
numbers 9 and 12) damaged?
YES : Repair harness wire and then check that diagnostic
trouble code 15 is not output.
NO : Check that diagnostic trouble code 15 is not output. If
diagnostic trouble code 15 is output, replace the
auto-cruise control-ECU (Refer to
.). Then
check that diagnostic trouble code 15 is not output.
DTC 16: Auto-cruise Control-ECU
.
DTC SET CONDITIONS
This code is output when a problem is found on the
cancel status hold circuit or microcomputer operation
monitor circuit, which is incorporated in the
auto-cruise control-ECU.
.
TROUBLESHOOTING HINTS
Malfunction of the auto-cruise control-ECU.
AC106551AB
CONNECTORS: C-82, C-84, C-96
C-96
C-84
C-82
CLOCK SPRING
AC001451
CONNECTOR: C-20
AB
AC106551AC
CONNECTORS: C-82
CLOCK SPRING
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-40
DIAGNOSIS
Replace the auto-cruise control-ECU. (Refer to
Check that diagnostic trouble code 16 is not output.
DTC 17: Throttle Position Sensor and Idle Position Signal System
AC304741AB
Throttle Position Sensor System Circuit
AC103106AB
CONNECTOR: B-07 <2.4L ENGINE>
AC103107
CONNECTOR: B-07 <3.0L ENGINE>
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст