Mitsubishi Eclipse. Manual — part 893
CLUTCH
TSB Revision
CLUTCH OVERHAUL
21B-3
<3.0L ENGINE>
AKX00761
19 ± 3 N·m
14 ± 2 ft-lb
9.8 ± 2 N·m
87 ± 17 in-lb
19 ± 3 N·m
14 ± 2 ft-lb
15 ± 2 N·m
11 ± 1 ft-lb
19 ± 3 N·m
14 ± 2 ft-lb
23 ± 2 N·m
17 ± 1 ft-lb
3
2
13
10
1
9
14
8
7
5
6
4
22
23
21
20
16
15
17
19
11
12
AB
18
18
REMOVAL STEPS
1.
CLUTCH FLUID LINE BRACKET
2.
INSULATOR
3.
WASHER
4.
CLUTCH TUBE
5.
UNION BOLT
6.
UNION
7.
GASKET
8.
VALVE
9.
VALVE SPRING
10. CLUTCH RELEASE CYLINDER
>>B<<
11. CLUTCH COVER
>>B<<
12. CLUTCH DISC
>>E<<
13. SEALING CAP
14. RELEASE FORK SHAFT
15. SUPPORT SPRING (L)
16. PACKING
>>D<<
17. RELEASE FORK
>>C<<
18. BUSHING
19. CLUTCH RELEASE BEARING
20. PACKING
21. SUPPORT SPRING (R)
22. RELEASE FORK BOOT
23. MAINTENANCE HOLE COVER
REMOVAL STEPS (Continued)
CLUTCH
TSB Revision
CLUTCH OVERHAUL
21B-4
REMOVAL SERVICE POINT
.
<<A>> RELEASE FORK REMOVAL
Move the release fork in the direction shown to remove the clip
from the fulcrum.
INSTALLATION SERVICE POINTS
.
>>A<< RELEASE FORK INSTALLATION
1. Apply Mitsubishi genuine grease part number 0101011 or
equivalent to the illustrated positions of the release fork.
2. Install the release fork to the fulcrum.
.
AKX00752
FULCRUM
CLIP
RELEASE FORK
AB
AKX00753
APPLY
GREASE
APPLY
GREASE
APPLY
GREASE
AB
CLUTCH
TSB Revision
CLUTCH OVERHAUL
21B-5
>>B<< CLUTCH DISC AND CLUTCH COVER
INSTALLATION
1. Apply Mitsubishi genuine grease part number 0101011 or
equivalent to the clutch disc splines and rub it in the splines
with a brush.
2. Using the clutch disc guide to position the clutch disc on the
flywheel.
3. Install the clutch cover onto the flywheel.
.
>>C<< OUTER RACE INSTALLATION
Press in the bushing into the release fork to the position shown
in the illustration.
.
AKX00759
FLYWHEEL
CLUTCH DISC
CLUTCH
DISC
GUIDE
CLUTCH
COVER
AB
AKX00755
BUSHING
AB
CLUTCH
TSB Revision
CLUTCH OVERHAUL
21B-6
>>D<< RELEASE FORK INSTALLATION
Apply Mitsubishi genuine grease part number 0101011 or
equivalent to the illustrated positions of the release fork.
.
>>E<< SEALING CAP INSTALLATION
Press in the sealing cap to the position shown in the illustration.
Be sure that it is not installed in a slanted position.
CLUTCH INSPECTION
M1212001100036
.
CLUTCH COVER
1. Check the diaphragm spring end for wear and uneven
height. Replace if wear is evident or height difference
exceeds the limit.
Limit: 0.5 mm (0.020 inch)
2. Check the pressure plate surface for wear, cracks and
discoloration.
3. Check the rivets of the strap plate for looseness. If loose,
replace the clutch cover.
.
AKX00757
APPLY
GREASE
APPLY
GREASE
PACK
GREASE
AB
AKX00756
2 mm (0.08 in)
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст