Mitsubishi Eclipse. Manual — part 847
SPECIAL TOOLS
TSB Revision
AUTOMATIC TRANSAXLE
23A-397
STEP 3. Check the lock cam.
Q: Is the lock cam in good condition?
YES :
Go to Step 4.
NO :
Replace the lock cam. Refer to
.
Check that the ignition key can not be
turned to the "LOCK" (OFF) position with
the selector lever at any position other than
"P" position.
STEP 4. Check the fit of the key interlock cable.
Q: Is the key interlock cable installed correctly?
YES :
Go to Step 5.
NO :
Install the key interlock cable correctly.
Refer to
. Check that the ignition
key cannot be turned to the "LOCK" (OFF)
position with the selector lever at any
position other than "P" position.
STEP 5. Check the key interlock cable.
Q: Is the key interlock cable in good condition?
YES :
Go to Step 6.
NO :
Replace the key interlock cable. Refer to
. Check that the ignition key
cannot be turned to the "LOCK" (OFF)
position with the selector lever at any
position other than "P" position.
STEP 6. Check the fit of the transaxle control
cable.
Q: Is the transaxle control cable installed correctly?
YES :
Replace the steering lock cylinder
assembly. Refer to
and
Check that the ignition key can not be
turned to the "LOCK" (OFF) position with
the selector lever at any position other than
"P" position.
NO :
Install the transaxle control cable correctly.
Refer to
. Check that the ignition
key can not be turned to the "LOCK" (OFF)
position with the selector lever at any
position other than "P" position.
SPECIAL TOOLS
M1231000600361
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION APPLICATION
MD998330 (Includes
MD998331)
Oil pressure gauge (3.0
MPa, 427 psi)
MD998330-01
Measurement of hydraulic
pressure
MD998332
Adapter
MD998332-01
Connection for oil pressure
gauge
MD998478
Test harness (3 pin,
triangle)
MD998478-01
Inspection using an oscilloscope
AC103525
SPECIAL TOOLS
TSB Revision
AUTOMATIC TRANSAXLE
23A-398
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991914
F: MB991825
G: MB991826
MUT-III sub assembly
A: Vehicle
Communication
Interface (V.C.I.)
B: MUT-III USB Cable
C: MUT-III Main Harness
A (Vehicles with CAN
communication
system)
D: MUT-III Main Harness
B (Vehicles without
CAN communication
system)
E: MUT-III Main Harness
C (for Daimler Chrysler
models only)
F: MUT-III Adapter
Harness
G: MUT-III Trigger
Harness
−
Checking diagnostic trouble
codes
MB991709
Test harness set
Tool not available
Inspection using an oscilloscope
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION APPLICATION
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
DO NOT USE
A
B
C
D
E
F
G
DO NOT USE
SPECIAL TOOLS
TSB Revision
AUTOMATIC TRANSAXLE
23A-399
MD998900
Adapter
MD998900-01
Connection for oil pressure
gauge
MB995062
Flushing tool
−
Flushing cooler and tube
MB991453
Engine hanger assembly
MZ203827-01
When the engine hanger is
used: Supporting the engine
assembly during removal and
installation of the transaxle
assembly
NOTE: Special tool MB991454
is a part of engine hanger
attachment set MB991453.
GENERAL SERVICE
TOOL MZ203827
Engine lifter
MZ203827-01
MB991454
Engine hanger balancer
MZ203827-01
MB991895
Engine hanger
−
MB991928
Engine hanger
A: MB991929
Joint (50)
×2
B: MB991930
Joint (90)
×2
C: MB991931
Joint (140)
×2
D: MB991932
Foot (standard)
×4
E: MB991933
Foot (short)
×2
F: MB991934
Chain and hook
assembly
−
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION APPLICATION
B991453
MZ203827
B991454
MB991895
B991928
A
B
C
D
E
F
SLIDE BRACKET (HI)
SPECIAL TOOLS
TSB Revision
AUTOMATIC TRANSAXLE
23A-400
MB991897
Ball joint remover
MB991113-01,
MB990635-01 or
general service
tool
Knuckle and tie rod end ball joint
breakaway torque check
NOTE: Steering linkage puller
(MB990635 or MB991113) is
also used to disconnect knuckle
and tie rod end ball joint.
TOOL
TOOL NUMBER AND
NAME
SUPERSESSION APPLICATION
AC106827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст