Mitsubishi Eclipse. Manual — part 119
ENGINE ASSEMBLY
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-25
(1) Assemble the engine hanger (special tool
MB991928).Set following parts the base hanger.
• Slide bracket (HI)
• Foot (standard) (MB991932)
• Foot (short) (MB991933)
• Joint (50) (MB991929)
• Joint (90) (MB991930)
• Joint (140) (MB991931)
(2) Remove the chain block and support the engine
assembly with special tools MB991895.
.
>>D<< FUEL HIGH-PRESSURE HOSE INSTALLATION
CAUTION
Do not allow engine oil to enter the fuel rail.
1. Apply a small amount of new engine oil to the O-ring.
2. Turning the fuel high-pressure hose to the right and left,
install it to the fuel rail, while being careful not to damage the
O-ring. After installing, check that the hose turns smoothly.
3. If the hose does not turn smoothly, the O-ring may be
clamped. Disconnect the fuel high-pressure hose and check
the O-ring for damage.
4. Re-insert the fuel rail and check that the hose turns
smoothly.
AC302468
FOOT (SHORT) (MB991933)
JOINT (90)
(MB991930)
FOOT (STANDARD)
(MB991932)
JOINT (50)
(MB991929)
JOINT (140)
(MB991931)
FRONT S
SLIDE BRACKET (HI)
AB
AC102341AC
MB991454
AC302400AC
MB991928
SLIDE BRACKET (HI)
MB991454
MB991932
MB991931
MB991933
MB991929
MB991930
AC000129 AB
FUEL RAIL
HIGH-PRESSURE
FUEL HOSE
O-RING
CAMSHAFT AND CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-26
CAMSHAFT AND CAMSHAFT OIL SEAL
REMOVAL AND INSTALLATION
M1112001900325
<LEFT BANK>
Required Special Tools:
• MB990767: End Yoke Holder
• MB991559: Camshaft Oil Seal Adapter
• MD998443: Auto-lash Adjuster Holder
• MD998713: Camshaft Oil Seal Installer
• MD998715: Crankshaft Pulley Holder Pin
Pre-removal and Post-installation Operation
Timing Belt Removal and Installation (Refer to
AC004834
APPLY ENGINE OIL TO
ALL THE MOVING PARTS
WHEN INSTALLING
(ENGINE OIL)
3.4 ± 0.5 N·m
31 ± 4 in-lb
13 ± 2 N·m
109 ± 21 in-lb
88 ± 10 N·m
65 ± 7 ft-lb
31 ± 3 N·m
23 ± 2 ft-lb
1
2
3
5
6
7
8
10
11
AC
4
N
9
N
CAMSHAFT REMOVAL STEPS
•
THERMOSTAT HOUSING
ASSEMBLY (REFER TO GROUP
14, WATER HOSE AND PIPE
1.
BLOW-BY HOSE CONNECTION
2.
PCV HOSE CONNECTION
3.
SPARK PLUG CABLE
4.
BATTERY CABLE CONNECTION
5.
ROCKER COVER
<<A>> >>D<<
6.
ROCKER ARM AND SHAFT
ASSEMBLY
<<B>> >>B<<
7.
CAMSHAFT SPROCKET
9.
BATTERY CABLE AND
HARNESS BRACKET
10. THRUST CASE
11. CAMSHAFT
CAMSHAFT OIL SEAL
REMOVAL STEPS
<<B>> >>B<<
7.
CAMSHAFT SPROCKET
>>A<<
8.
CAMSHAFT OIL SEAL
CAMSHAFT REMOVAL STEPS
CAMSHAFT AND CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-27
<RIGHT BANK>
Required Special Tools:
• MB990767: End Yoke Holder
• MD998443: Auto-lash Adjuster Holder
• MD998713: Camshaft Oil Seal Installer
• MD998715: Crankshaft Pulley Holder Pin
Pre-removal and Post-installation Operation
Timing Belt Removal and Installation (Refer to
AC001717AB
3.4 ± 0.5 N·m
31 ± 4 in-lb
13 ± 2 N·m
109 ± 21 in-lb
31 ± 3 N·m
23 ± 2 ft-lb
88 ± 10 N·m
65 ± 7 ft-lb
APPLY ENGINE OIL TO
ALL THE MOVING PARTS
WHEN INSTALLING
1
2
3
4
5
6
7
8
9
CAMSHAFT REMOVAL STEPS
•
INTAKE MANIFOLD PLENUM
(REFER TO GROUP 15, INTAKE
MANIFOLD PLENUM
.)
1.
BREATHER HOSE
CONNECTION
2.
BLOW-BY HOSE CONNECTION
3.
SPARK PLUG CABLE
4.
ROCKER COVER
<<A>> >>D<<
5.
ROCKER ARM AND SHAFT
ASSEMBLY
>>C<<
6.
DISTRIBUTOR
<<B>> >>B<<
7.
CAMSHAFT SPROCKET
9.
CAMSHAFT
CAMSHAFT OIL SEAL
REMOVAL STEPS
<<B>> >>B<<
7.
CAMSHAFT SPROCKET
>>A<<
8.
CAMSHAFT OIL SEAL
CAMSHAFT REMOVAL STEPS
CAMSHAFT AND CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-28
REMOVAL SERVICE POINTS
.
<<A>> ROCKER ARM AND SHAFT ASSEMBLY REMOVAL
1. Install special tool MD998443 as shown in the illustration so
that the lash adjusters will not fall out.
CAUTION
Never disassemble the rocker arm and shaft assembly.
2. Loosen the rocker arm and shaft assembly mounting bolts,
then remove the rocker arm and shaft assembly with the
bolts still attached.
.
<<B>> CAMSHAFT SPROCKET REMOVAL
1. Use special tools MB990767 and MD998715 to loosen the
camshaft sprocket mounting bolt.
2. Remove the camshaft sprocket.
INSTALLATION SERVICE POINTS
.
>>A<< CAMSHAFT OIL SEAL INSTALLATION
1. Apply engine oil to the camshaft oil seal lip.
2. Use special tools MB991559 and MD998713 to press-fit the
camshaft oil seal.
.
>>B<< CAMSHAFT SPROCKET INSTALLATION
1. Install the camshaft sprocket.
AC001718
MD998443
AB
ACX00301AB
MB990767
MD998715
AC001719 AB
MD998713
MB991559 MD998713
LEFT BANK
RIGHT BANK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст