Mitsubishi Eclipse. Manual — part 120
CAMSHAFT AND CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-29
2. Use special tools MB990767 and MD998715 to tighten the
camshaft sprocket mounting bolt to the specified torque.
Tightening torque: 88
± 10 N⋅m (65 ± 7 ft-lb)
.
>>C<< DISTRIBUTOR INSTALLATION
1. Align the timing mark of the camshaft sprocket (right bank)
with that of the cylinder head.
2. Align the mating marks on the distributor housing and
coupling, then install the distributor to the engine.
.
>>D<< ROCKER ARM AND SHAFT ASSEMBLY
INSTALLATION
1. Rotate the camshaft until the dowel pin on its front end is
located as shown in the illustration.
NOTE: Placing the camshaft in the illustrated position mini-
mizes the amount of cam lift, making it easier to install the
rocker arm and shaft assembly.
2. Temporarily tighten the rocker shaft with the bolts so that all
rocker arms on the inlet valve side do not push the valves.
ACX00301AB
MB990767
MD998715
AC001720
TIMING
MARKS
CAMSHAFT
SPROCKET
(RIGHT BANK)
AB
AC001721AB
MATING MARKS
AC001722
APPROXIMATELY 60˚
APPROXIMATELY 70˚
RIGHT BANK
LEFT BANK
AB
CAMSHAFT AND CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-30
3. Position the rocker shaft spring so that it takes a right angle
against the plug guide.
NOTE: Set the rocker shaft spring before installing the
rocker arm and shaft assembly on the exhaust side.
4. Tighten the rocker arm and shaft assembly mounting bolts to
the specified torque.
Tightening torque: 31
± 3 N⋅m (23 ± 2 ft-lb)
5. Remove special tool MD998443.
ACX00378
PLUG GUIDE
ROCKER SHAFT SPRING
ROCKER SHAFT
SPRING
PLUG GUIDE
AB
OIL PAN
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-31
OIL PAN
REMOVAL AND INSTALLATION
M1112002800677
REMOVAL SERVICE POINTS
.
<<A>> LOWER OIL PAN REMOVAL
1. Remove the oil pan, lower mounting bolts.
Pre-removal and Post-installation operation
• Engine Oil Draining and Refilling (Refer to GROUP 12, On-vehicle Service − Engine Oil Replacement
.)
• Front Exhaust Pipe Removal and Installation (Refer to GROUP 15, Exhaust Pipe, Main Muffler and Catalytic Converter
AC001723 AB
48 ± 6 N·m
36 ± 4 ft-lb
30 ± 3 N·m
23 ± 2 ft-lb
30 ± 3 N·m
23 ± 2 ft-lb
35 ± 6 N·m
26 ± 4 ft-lb
5.9 ± 1.0 N·m
52 ± 9 in-lb
11 ± 1 N·m
96 ± 8 in-lb
39 ± 5 N·m
29 ± 4 ft-lb
1
2
3
4
5
6
7
8
9
7
9
SEALANT:
MITSUBISHI GENUINE PART
NO. MD970389 OR
EQUIVALENT
(ENGINE OIL)
GROOVE
BOLT HOLE
Ø 4 mm
(0.2 in)
LOWER OIL PAN REMOVAL
STEPS
1.
DRAIN PLUG
>>C<<
2.
DRAIN PLUG GASKET
<<A>>
>>B<<
7.
LOWER OIL PAN
UPPER OIL PAN REMOVAL
STEPS
1.
DRAIN PLUG
>>C<<
2.
DRAIN PLUG GASKET
3.
STARTER CONNECTOR
4.
STARTER
5.
OIL DIPSTICK AND DIPSTICK
GUIDE
6.
O-RING
<<A>>
>>B<<
7.
LOWER OIL PAN
8.
OIL PAN BOLT HOLE COVER
<<B>>
>>A<<
9.
UPPER OIL PAN
UPPER OIL PAN REMOVAL
STEPS (Continued)
OIL PAN
TSB Revision
ENGINE MECHANICAL <3.0L>
11C-32
CAUTION
Do not use the oil pan remover (MD998727). It will damage
the upper oil pan.
2. Place a wooden block against the lower oil pan as shown in
the illustration and remove by tapping with a hammer.
.
<<B>> UPPER OIL PAN REMOVAL
1. Remove the upper oil pan mounting bolts.
2. Screw the bolts (M10) securing the upper oil pan to the
transaxle assembly in the illustrated bolt holes, then remove
the upper oil pan.
INSTALLATION SERVICE POINTS
.
>>A<< UPPER OIL PAN INSTALLATION
CAUTION
The bolt holes for bolts 13 and 14 in the illustration are cut
away on the transaxle side. Be careful not to insert these
bolts at an angle.
Tighten the oil pan, upper mounting bolts in the order shown.
AC001724
LOWER OIL PAN
AB
AC001725
AC001726AB
1
4
8
5
12
9
2
3
7
11
6
10
16
15
13
14
UPPER OIL PAN
REAR OIL
SEAL CASE
TRANSAXLE
SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст