Mitsubishi Galant. Manual — part 486
REAR AXLE HUB ASSEMBLY
TSB Revision
REAR AXLE
27-7
REMOVAL SERVICE POINTS
<<A>> CALIPER ASSEMBLY REMOVAL
Remove the caliper assembly and suspend it.
<<B>> ABS ROTOR REMOVAL
<<C>> BACKING PLATE REMOVAL
Remove the backing plate and suspend it.
INSTALLATION SERVICE POINT
>>A<< ABS ROTOR INSTALLATION
INSPECTION
M1271002100043
•
Check the oil seal for crack or damage.
•
Check the ABS rotor for chipped teeth.
AC001185
SOCKET
AB
MB991248
AC001186 AB
ABS ROTOR
SOCKET
KNUCKLE
TSB Revision
REAR AXLE
27-8
K N U C K LE
REMOVAL AND INSTALLATION
M1271003000049
CAUTION
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in the unladen condition.
Required Special Tool:
MB991113 or MB990635: Steering Linkage Puller
Pre-removal Operation
Rear Axle Hub Assembly Removal (Refer to
Post-installation Operation
•
Check the Dust Cover for Cracks or Damage by Pushing
It with Finger.
•
Rear Axle Hub Assembly Installation (Refer to
AC001187
128 – 137 N·m*
87 – 101 ft-lb*
28 N·m
21 ft-lb
108 N·m*
80 ft-lb*
98 N·m*
72 ft-lb*
1
7
6
5
4
3
2
AC
98 N·m
72 ft-lb
REMOVAL STEPS
1.
TRAILING ARM CONNECTION
2.
LOWER ARM CONNECTION
<<A>>
3.
TOE CONTROL ARM
CONNECTION
4.
SHOCK ABSORBER
CONNECTION
5.
UPPER ARM CONNECTION
6.
HUB CAP <VEHICLES WITHOUT
ABS>
7.
KNUCKLE
REMOVAL STEPS (Continued)
SPECIFICATIONS
TSB Revision
REAR AXLE
27-9
REMOVAL SERVICE POINT
<<A>> TOE CONTROL ARM DISCONNECTION
CAUTION
•
Use special tool MB991113 or MB990635 to loosen the
nut from the ball joint instead of removing it.
•
Hang special tool MB991113 or MB990635 with ropes to
prevent it from falling.
INSPECTION
M1271003100035
Check the knuckle for wear or cracks.
SPECIFIC ATIO NS
FASTENER TIGHTENING SPECIFICATIONS
M1271004000042
SERVICE SPECIFICATIONS
M1271000300041
ACX01123AB
NUT
BALL JOINT
CORD
MB991113 OR MB990635
ITEMS
SPECIFICATIONS
Knuckle
Lower arm assembly to knuckle jam nut
108 N
⋅
m (80 ft-lb)
Shock absorber assembly to knuckle bolt
98 N
⋅
m (72 ft-lb)
Toe control arm assembly to knuckle jam nut
28 N
⋅
m (21 ft-lb)
Trailing arm assembly to knuckle nut
118
−
137 N
⋅
m (87
−
101 ft-lb)
Upper arm assembly to knuckle nut
98 N
⋅
m (72 ft-lb)
Rear axle hub assembly
Brake caliper assembly bolt
55
−
65 N
⋅
m (41
−
48 ft-lb)
Rear hub assembly bolt
74
−
88 N
⋅
m (55
−
56 ft-lb)
ITEMS
LIMIT
Wheel bearing end play mm (in)
0.05 (0.002)
Rear hub rotary-sliding resistance N
⋅
m (ft-lb)
18 (13)
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст