Mitsubishi Galant. Manual — part 582
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-13
NOTE: For removal and installation of the clock
spring and column switch assembly (windshield
wiper and washer switch), refer to GROUP 54A,
Steering Wheel and Shaft switch
REMOVAL SERVICE POINT
<<A>> WIPER MOTOR REMOVAL
CAUTION
Auto-stop angle is preadjusted at the factory. Therefore do
not remove the crank arm from the wiper motor unless
necessary. Should it be removed, mark the crank arm and
wiper motor.
Use a flat-tipped screwdriver to disconnect the wiper motor
crank arm from the link assembly.
INSTALLATION SERVICE POINT
>>A<< WIPER ARM AND BLADE ASSEMBLY
INSTALLATION
Install the wiper blade at the specified position (standard
value).
Standard value:
Driver's side: 20
−−−−
30 mm (0.8
−−−−
1.2 inches)
Passenger's side: 30
−−−−
45 mm (1.2
−−−−
1.8 inches)
WASHER NOZZLE REMOVAL
STEPS
7.
WASHER HOSE
8.
WASHER NOZZLE
WASHER TANK REMOVAL STEPS
•
WASHER FLUID DRAINING AND
APPLYING
7. WASHER HOSE
9. WASHER TANK ASSEMBLY
10. WASHER MOTOR
WASHER TANK REMOVAL STEPS
AC000660
WIPER MOTOR
CRANK ARM
WIPER LINK
ASSEMBLY
AB
AC003673AB
FRONT DECK GARNISH END
PASSENGER'S
SIDE
DRIVER'S SIDE
WINDSHIELD WIPER AND WASHER
TSB Revision
EXTERIOR
51-14
INSPECTION
M1511007700120
WIPER MOTOR CHECK
Check the wiper motor after disconnecting the wiring harness
connector, and with the wiper motor remaining installed to the
body.
Wiper Motor at Low-Speed and High-Speed Operation
Connect a battery to the wiper motor as shown in the
illustration, and check motor operation at low-speed and high-
speed.
Wiper Motor at Stop Position Operation
1. Run the wiper motor at low-speed, disconnect the battery,
and stop the motor.
2. Reconnect the battery as shown in the illustration, and
confirm that after the motor starts turning at low-speed, and
stops at the automatic stop position.
WASHER MOTOR CHECK
1. With the washer motor installed to the washer tank, fill the
washer tank with water.
2. Check that the water squirts out strongly when battery
voltage is applied to terminals (1) and (2).
WINDSHIELD WIPER AND WASHER SWITCH
CHECK
1. Windshield wiper and washer switch
AC003574
INSPECTION WHILE OPERATING
INSPECTION WHILE STOPPED
LOW-
SPEED
HIGH-
SPEED
LOW-
SPEED
HIGH-
SPEED
AB
AC003575
SWITCH POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
OFF
−
No continuity
Windshield wiper mist
switch ON
23
−
32
Continuity
Windshield intermittent
wiper switch ON
23
−
31
Continuity
21
22
23
24
25
26
27
28
29
30
31
32
AC002017
UPPER SIDE
AB
MARK
TSB Revision
EXTERIOR
51-15
2. Windshield intermittent wiper interval adjusting knob
Measure the resistance value at terminal numbers 27 and
28. The resistance value should rise smoothly from
approximately 0
Ω
("FAST" position) to approximately 1 k
Ω
("SLOW" position).
WASHER FLUID EJECTION POINT CHECK
Adjust the ejection angle by moving a ball in the nozzle.
A: 430 mm (16.9 inches)
B: 260 mm (10.2 inches)
C: 325 mm (12.8 inches)
D: 350 mm (13.8 inches)
E: 70 mm (2.8 inches)
F: 50 mm (2.0 inches)
M A R K
REMOVAL AND INSTALLATION
M1511011800078
Windshield low-speed
wiper switch ON
23
−
30
Continuity
Windshield high-speed
wiper switch ON
21
−
23
Continuity
Windshield washer
switch ON
22
−
23
Continuity
SWITCH POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
AC003576AB
A
A
B
B
C
D
E
F
RH
LH
CERAMIC END LINE
AC003577
1
2
3
4
5
1
A
1. TOP MARK
>>A<<
2. ENGINE SPECIFICATION MARK
(V6)
>>A<<
3. GRADE MARK (DE, ES, LS, GTZ)
>>A<<
4. "GALANT" MARK
>>A<<
5. "MITSUBISHI" MARK
MARK
TSB Revision
EXTERIOR
51-16
INSTALLATION SERVICE POINT
>>A<< MARK INSTALLATION
1. Installation position Attach to the position shown in the
illustration.
AC003578AB
LH SIDE
130 mm (5.1 in)
61 mm
(2.4 in)
83.5 mm
(3.29 in)
136.5 mm
(5.37 in)
FRONT DDOR
OPENING LINE
FENDER
PRESS LINE
NOTE
RH side is symmetrical on LH side.
ENGINE SPECIFICATION MARK
AC003579AB
28.4 mm
(1.12 in)
24.2 mm
(0.95 in)
15.8 mm
(0.62 in)
TRUNK LID
END LINE
TRUNK LID
PRESS LINE
27.9 mm
(1.10 in)
24.2 mm
(0.95 in)
15.8 mm
(0.62 in)
TRUNK LID
PRESS LINE
TRUNK LID
END LINE
GRADE MARK
DE (also applicable ES, LS)
GTZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст