Mitsubishi Galant. Manual — part 634
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-89
SYMPTOM PROCEDURES
Inspection Procedure 1: When power switch is turned "ON," no power is available.
AC003974 AB
Radio, Tape Player and CD Player Power Supply Circuit
AC003089
CONNECTOR: C-31
AT
AC003079 AB
CONNECTOR
BLOCK (LH)
CONNECTOR: C-66
TSB Revision
CHASSIS ELECTRICAL
RADIO WITH TAPE PLAYER AND CD PLAYER
54A-90
CIRCUIT OPERATION
Power is supplied to the radio, tape player, CD player
and CD auto changer when the ignition switch is at
the "ACC" or "ON" position.
TECHNICAL DESCRIPTION (COMMENT)
The cause is probably a faulty radio, tape player, CD
player and CD auto changer power supply circuit
system.
TROUBLESHOOTING HINTS
•
Damaged harness wire or connector.
•
Malfunction of the radio, tape player, CD player
and CD auto changer.
DIAGNOSIS
Required Special Tool:
•
MB991223: Harness set
STEP 1. Check the radio, tape player, CD player and CD
auto changer power supply circuit by backprobing.
(1) Do not disconnect radio, tape player, CD player and CD
auto changer connector C-31.
(2) Turn the ignition switch to "ACC" position.
(3) Measure the voltage between terminal 10 and ground by
backprobing.
Q: Is the voltage approximately 12 volts (battery positive
voltage)?
YES : Go to Step 4.
NO : Go to Step 2.
STEP 2. Check radio, tape player, CD player and CD auto
changer connector C-31 for damage.
Q: Are radio and CD player and CD auto changer
connector C-31 in good condition?
YES : Go to Step 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. If the power switch is
turned on, the radio and CD player and CD auto
changer should operate normally.
AC003082AD
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-73
AC003080 AB
JUNCTION BLOCK
(REAR VIEW)
CONNECTOR: C-84
1
2
3
4
5
6
7
8
9
10
11
12
13
14
ACX01854AD
CONNECTOR C-31
(HARNESS SIDE)
AC003089
CONNECTOR: C-31
AT
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-91
STEP 3. Check the harness wires between radio, tape
player, CD player and CD auto changer connector C-31 and
ignition switch (ACC).
NOTE: After inspecting intermediate connector C-66 and
junction block connectors C-73 and C-84, inspect the wire. If
intermediate connector C-66 and junction block connectors C-
73 and C-84 are damaged, repair or replace them. Refer to
GROUP 00E, Harness Connector Inspection
Q: Are the harness wires between radio, tape player, CD
player and CD auto changer connector C-31 and ignition
switch (ACC) in good condition?
YES : There is no action to be taken.
NO : repair them. If the power switch is turned on, the
radio, tape player, CD player and CD auto changer
should operate normally.
AC003089
CONNECTOR: C-31
AT
AC003079 AB
CONNECTOR
BLOCK (LH)
CONNECTOR: C-66
AC003082AD
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-73
AC003080 AB
JUNCTION BLOCK
(REAR VIEW)
CONNECTOR: C-84
TSB Revision
CHASSIS ELECTRICAL
RADIO WITH TAPE PLAYER AND CD PLAYER
54A-92
STEP 4. Check that the radio, tape player, CD player, and
the CD auto changer are installed correctly.
NOTE: The radio, tape player, CD player and CD auto changer
are grounded to the instrument panel center reinforcement
directly.
Q: Are the radio, tape player, CD player and CD auto
changer installed correctly?
YES : Repair or replace the radio, tape player, CD player
and CD auto changer. If the power switch is turned
on, the radio, tape player, CD player and CD auto
changer should operate normally.
NO : Install properly If the power switch is turned on, the
radio, tape player, CD player and CD auto changer
should operate normally.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст