Mitsubishi Galant. Manual — part 25
CAMSHAFT AND CAMSHAFT OIL SEAL
TSB Revision
ENGINE MECHANICAL <2.4L>
11A-19
5. Make sure that the notch in the end of the rocker arm shaft
is facing the direction shown.
>>B<< CAMSHAFT OIL SEAL INSTALLATION
1. Apply engine oil to the camshaft oil seal lip.
2. Use special tool MD998713 to press-fit the camshaft oil
seal.
>>C<< CAMSHAFT SPROCKET INSTALLATION
1. Install the camshaft sprocket.
2. Use special tools MB990767 and MD998719 to tighten the
camshaft sprocket securing bolt to the specified torque.
Tightening torque: 88 N
⋅⋅⋅⋅
m (65 ft-lb)
AC000131
NOTCH
AB
ACX00372 AC
MD998713
ACX00301
MB990767
MD998719
AC
OIL PAN
TSB Revision
ENGINE MECHANICAL <2.4L>
11A-20
O IL PA N
REMOVAL AND INSTALLATION
M1112002800127
Required Special Tool:
•
MD998727: Oil Pan Remover
Pre-removal and Post-installation Operation
•
Engine Oil Draining and Refilling (Refer to GROUP 12,
On-vehicle Service
−
Engine Oil Replacement
•
Oil Dipstick Removal and Installation
•
Front Exhaust Pipe Removal and Installation (Refer to
GROUP 15, Exhaust Pipe and Main Muffler
.)
AC000132
SEALANT:
MITSUBISHI GENUINE PART
NO.MD970389 OR EQUIVALENT
Ø 4 mm
(0.2 in)
GROOVE
BOLT HOLE
1
4
3
N
2
39 N·m
29 ft-lb
6.9 N·m
61 in-lb
25 N·m
18 ft-lb
8.8 N·m
78 in-lb
AC
REMOVAL STEPS
1.
DRAIN PLUG
>>B<<
2.
DRAIN PLUG GASKET
3.
BELL HOUSING COVER
<<A>>
>>A<<
4.
OIL PAN
REMOVAL STEPS (Continued)
OIL PAN
TSB Revision
ENGINE MECHANICAL <2.4L>
11A-21
REMOVAL SERVICE POINT
<<A>> OIL PAN REMOVAL
CAUTION
Perform this slowly to avoid deformation of the oil pan
flange.
After removing the oil pan mounting bolts, remove the oil pan
with special tool MD998727 and a brass bar.
INSTALLATION SERVICE POINTS
>>A<< OIL PAN INSTALLATION
1. Remove sealant from the oil pan and cylinder block mating
surfaces.
2. Degrease the sealant-coated surface and the engine mating
surface.
3. Apply MITSUBISHI GENUINE PART number MD970389 or
equivalent around the gasket surface of the oil pan.
NOTE: The sealant should be applied in a continuous bead
approximately 4 mm (0.2 inch) in diameter.
CAUTION
After installing the oil pan, wait at least one hour before
starting the engine.
4. Assemble the oil pan to the cylinder block within 15 minutes
after applying the sealant.
Be careful when installing the oil pan. The bolts indicated in
the illustration have different lengths from the other bolts.
>>B<< DRAIN PLUG GASKET INSTALLATION
Install the drain plug gasket in the direction shown in the
illustration.
ACX00366
MD998727
MD998727
AB
AC000133
M6 × 8mm
FRONT OF ENGINE
AB
ACX00364
DRAIN PLUG
GASKET
OIL PAN
SIDE
AB
CRANKSHAFT FRONT OIL SEAL
TSB Revision
ENGINE MECHANICAL <2.4L>
11A-22
INSPECTION
M1112002900072
•
Check the oil pan for cracks.
•
Check the oil pan sealant-coated surface for damage and
deformation.
C R A N K SH A FT FR O N T O IL SEA L
REMOVAL AND INSTALLATION
M1112003400100
Required Special Tools:
•
MB991367: Special Spanner
•
MB998375: Crankshaft Front Oil Seal Installation
Pre-removal and Post-installation Operation
•
Timing Belt Removal and Installation (Refer to
•
Crankshaft Position Sensor Removal and Installation
(Refer to GROUP 16, Ignition System
−
Crankshaft
Position Sensor <2.4L Engine>
AC000134
ENGINE OIL
CRANKSHAHF
1
4
2
3
(ENGINE OIL)
108 – 127 N·m
80 – 94 ft-lb
N
5
AC
5
REMOVAL STEPS
<<A>>
>>B<<
1.
CRANKSHAFT SPROCKET
>>B<<
2.
CRANKSHAFT SENSING BLADE
•
TIMING BELT B (REFER TO
>>B<<
3.
CRANKSHAFT SPROCKET B
4.
KEY
>>A<<
5.
CRANKSHAFT FRONT OIL SEAL
REMOVAL STEPS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст