Mitsubishi Galant. Manual — part 648
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-145
Inspection Procedure 28: No sound. (CD only)
DIAGNOSIS
STEP 1. Check that the CD player plays properly
if another CD is inserted.
Q: Does it play properly if another CD is inserted?
YES :
The CD used is defective. The CD player
should sound normally.
NO :
Go to Step 2 .
STEP 2. Return it to the normal temperature, and
recheck the operation. Check that the CD player
operates properly.
Q: Return it to the normal temperature, and recheck
the operation. Does it operate properly?
YES :
The CD player should sound normally.
NO :
Repair or replace the CD player. The CD
player should sound normally.
Inspection Procedure 29: CD sound skips.
DIAGNOSIS
STEP 1. Malfunction occurrence state.
Q: When does a malfunction occur?
While parking :
Go to Step 2.
While driving :
Stop vehicle, go to Step 4.
STEP 2. Check that the CD face is scratched or
dirty.
Q: Is the CD face scratched or dirty?
YES :
CD is defective, or clean the CD. Check that
a CD sound skip is resolved.
NO :
Go to Step 3.
STEP 3. Check that the CD player plays properly
if another CD is started.
Q: Does it play properly if another CD is inserted?
YES :
CD is defective. Check that a CD sound
skip is resolved.
NO :
Repair or replace the CD player. Check that
a CD sound skip is resolved.
STEP 4. Check that sound skips when the side of
the CD player is tapped.
NOTE: Check by using a proper CD which is free
from scratches, dirt or any other abnormality.
Q: Does sound skip when the side of the CD player is
tapped?
YES :
Securely mount the CD player. Check that a
CD sound skip is resolved.
NO :
Check the sound skipping state in detail
while driving, and then contact a service
shop. Check that a CD sound skip is
resolved.
Inspection Procedure 30: Sound quality is poor.
DIAGNOSIS
STEP 1. Check that the CD player plays properly if another
CD is inserted.
Q: Does it play properly if another CD is inserted?
YES : CD used is defective. The sound quality should return
to normal.
NO : Repair or replace the CD player. The sound quality
should return to normal.
TSB Revision
CHASSIS ELECTRICAL
RADIO WITH TAPE PLAYER AND CD PLAYER
54A-146
Inspection Procedure 31: CD can not be ejected.
DIAGNOSIS
STEP 1. Check that the key switch (ignition key)
is at "ACC" or "ON".
Q: Is the key switch (ignition key) at "ACC" or "ON?"
YES :
Go to Step 2 .
NO :
Check the memory backup power supply
circuit. Refer to Inspection Procedure 22
STEP 2. Check that the combined amplifier or
radio set is connected securely.
Q: Is the combined amplifier or radio set connected
securely?
YES :
If the CD is not ejected, do not discard it,
because the player may be damaged.
Therefore, contact a service shop for
repairs. Check that a CD can be ejected
normally.
NO :
Connect the connectors securely. Check
that a CD can be ejected normally.
ON-VEHICLE SERVICE
PROCEDURE FOR INPUT OF ANTI-THEFT CODE
FOR ANTI-THEFT SYSTEM
M1544004400111
The radio, tape player and CD player do not work under the
following conditions:
•
Power supply to the radio, tape player and CD player has
been suspended for more than an hour continuously by
removing the cable from the battery terminal or
disconnecting the harness connectors.
•
The power supply to the radio, tape player and CD player
has been suspended for more than an hour due to a blown
fuse or discharged battery.
•
The radio, tape player and CD player has been replaced.
If the radio, tape player and CD player does not work for these
conditions, enter the security code as follows:
1. Confirm the security code using any of the following
methods.
(1) Use the security code indicated on the cards retained in
the vehicle.
ANTI-THEFT SYSTEM
Do not keep this card in your car!
For information the function and use of the
anti-theft coe see the owner's manual.
Code No.
Model
Serial No.
MITSUBISHI MOTORS CORPORATION
ACX02343AB
CARD
SECURITY CODE
RADIO WITH TAPE PLAYER AND CD PLAYER
TSB Revision
CHASSIS ELECTRICAL
54A-147
(2) If the security code is unknown owing to the owner's loss
of the card:
a. Remove the radio, tape player and CD player referring
.
b. Read the serial number stamped on the radio, tape
player and CD player.
c. Look up the security code (anti-theft code table)
corresponding to the serial number.
(3) When the radio, tape player and CD player is replaced:
Use the security code on the cards attached to the upper
surface of the replacement radio, tape player and CD
player.
NOTE: Deliver the two cards to the owner.
2. Connect the radio to the vehicle harness.
3. Turn the ignition key to the "ACC" or "ON" position.
4. Press the "PWR" button, and "codE" will be displayed.
AC003681
TYPICAL NAME CARD
AB
SERIAL NO.
AC003682
CARD
AB
AC002921
TAPE BUTTON
AB
MEMORY SELECT
BUTTON(1 TO 4)
PWR BUTTON
CD BUTTON
MEMORY SELECT
BUTTON(1 TO 4)
PWR BUTTON
TYPE 1
TYPE 2
TSB Revision
CHASSIS ELECTRICAL
RADIO WITH TAPE PLAYER AND CD PLAYER
54A-148
5. Press number 1 through number 4 memory select button to
set the four-digit security code shown on the card. Every
time each digit key is pressed, the figure changes as follows:
0 to 1 to 2 to 3 to 4 to 5 to 6 to 7 to 8 to 9 to 0
6. Press the "CD" button, and a beep will be heard. If entered
correctly, the radio and tape player will work.
7. If the security code is not accepted, "Err" is displayed. In a
few seconds, it will change to "codE." Then repeat steps 5
and 6.
NOTE: NOTE: The anti-theft system will allow three attempts
maximum to input the correct code.
NOTE: The second error is displayed as "2 Err." When the third
error is made, "3 Err" is displayed and then the display changes
to "oFF." If this should occur, the unit will not work any more.
NOTE: To input the security code again, turn the ignition switch
to the "ACC" or "ON" position and wait for one hour when "oFF"
is displayed. After "oFF" disappears on the display, press the
"PWR" button and "codE" will be displayed. The security code
can be input again.
Three-minute operation mode
To facilitate replacement or check, the radio, tape player and
CD player can be operated for three minutes without inputting
the security code.
1. Press the "PWR" button and "EJECT" button together to
operate the radio, tape player and CD player.
2. In three minutes the unit will not be able to work. Then the
radio, tape player and CD player will be switched off.
SPEAKER TEST
M1544005400084
Enter the speaker test mode according to the following steps:
1. Turn the Ignition switch to "ACC" or "ON" position and switch
off the radio, tape player, CD player and CD auto changer.
AC002922AB
DISPLAY
AC003683AB
TYPE 1
TYPE 2
PWR BUTTON
PWR BUTTON
EJECT BUTTON
EJECT BUTTON
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст