Mitsubishi Galant. Manual — part 430
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-187
STEP 5. Check harness for damage between solenoid
valve assembly connector B-38 terminal 7 and PCM
connector C-42 terminal 107.
Q: Is the harness wire in good condition?
YES : Go to Step 6.
NO : Repair it.
STEP 6. Check connector A-19X at A/T control relay for
damage.
Q: Is the connector in good condition?
YES : Go to Step 7.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
ACX02479
CONNECTOR: B-38
AF
AC004197
PCM
AF
CONNECTOR: C-42
AC004286 AC
A/T CONTROL
RELAY
BATTERY
CONNECTOR: A-19X
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-188
STEP 7. Check harness for damage between solenoid
valve assembly connector B-38 terminal 10 and A/T control
relay connector A-19X terminal 3.
Q: Is the harness wire in good condition?
YES : Go to Step 8.
NO : Repair it.
STEP 8. Using scan tool MB991502, check actuator test
item 06: Torque Converter Clutch Solenoid Valve.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Set scan tool MB991502 to the actuator test mode for item
06: Torque Converter Clutch Solenoid Valve.
•
An operation sound should be heard from solenoid
valve when the torque converter clutch solenoid valve is
operated.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the solenoid valve operating properly?
YES : This malfunction is intermittent. Refer to GROUP 00,
How to Use Troubleshooting/Inspection Service
Points
−
How to Cope with Intermittent Malfunction
NO : Replace the PCM.
ACX02479
CONNECTOR: B-38
AF
AC004286 AC
A/T CONTROL
RELAY
BATTERY
CONNECTOR: A-19X
AC003081AC
MB991502
DATA LINK
CONNECTOR
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-189
STEP 9. Check connector B-38 at solenoid valve assembly
for damage.
Q: Is the connector in good condition?
YES : Go to Step 10.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 10. Check the torque converter clutch solenoid valve
at solenoid valve assembly connector B-38.
(1) Disconnect connector B-38 and measure at the solenoid
valve side.
(2) Measure the resistance between terminal 7 and 10.
Standard value: 2.7
−−−−
3.4
Ω
Ω
Ω
Ω
Q: Is the resistance at the standard value?
YES : Go to Step 11.
NO : Replace the torque converter clutch solenoid valve.
Refer to GROUP 23B, Valve Body
ACX02479
CONNECTOR: B-38
AF
ACX02479
CONNECTOR: B-38
AF
AC001975
HARNESS
CONNECTOR: B-38
AE
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-190
STEP 11. Check the power supply voltage at solenoid
valve assembly connector B-38.
(1) Disconnect connector B-38 and measure at the harness
side.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 10 and ground.
•
Voltage should be battery positive voltage.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage normal?
YES : Go to Step 13.
NO : Go to Step 12.
STEP 12. Check connector A-19X at A/T control relay for
damage.
Q: Is the connector in good condition?
YES : Repair it because of harness open circuit or short
circuit to ground between solenoid valve assembly
connector B-38 terminal 10 and A/T control relay
connector A-19X terminal 3.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
STEP 13. Check connector C-42 at PCM connector for
damage.
Q: Is the connector in good condition?
YES : Go to Step 14.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
ACX02479
CONNECTOR: B-38
AF
AC001966
HARNESS
CONNECTOR: B-38
AE
AC004286 AC
A/T CONTROL
RELAY
BATTERY
CONNECTOR: A-19X
AC004197
PCM
AF
CONNECTOR: C-42
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст