Mitsubishi Galant. Manual — part 654
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-11
DIAGNOSTIC TROUBLE CODE PROCEDURES
DTC 11: ETACS-ECU fault
DTC SET CONDITION
DTC 11 is displayed when the ETACS-ECU detects
an error is its own data. This fault is limited to the
ETACS-ECU.
TROUBLESHOOTING HINT
Malfunction of the ETACS-ECU
DIAGNOSIS
Required Special Tool:
•
MB991502: Scan Tool (MUT-II)
Replace the ETACS-ECU.
Confirm that DTC 11 is not displayed.
Transmitter
The "LOCK" switch signal is not sent to
the ETACS-ECU.
N-17
The "UNLOCK" switch signal is not sent
to the ETACS-ECU.
The "PANIC" switch signal is not sent to
the ETACS-ECU.
SYMPTOMS
INSPECTION
PROCEDURE
REFERENCE
PAGE
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-12
DTC 12: Column switch fault or improper connection to the ETACS-ECU
Column Switch Power Supply and SWS Communication Circuit
AC004198
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-13
CIRCUIT OPERATION
•
The column switch (incorporated in ECU) is
energized by the battery and the ignition switch
(IG1). If one of the harness wires has an open
circuit, power will be supplied by the other active
harness wire.
•
If the column switch (incorporated in ECU)
receives a request signal from the ETACS-ECU,
the column switch will inform the SWS
communication line of various switch conditions.
DTC SET CONDITION
DTC 12 is displayed when the column switch
(incorporated in ECU) sends an abnormal signal to
the ETACS-ECU.
TROUBLESHOOTING HINTS
•
Malfunction of the column switch
•
Malfunction of the ETACS-ECU
•
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tools:
•
MB991223: Harness Set
•
MB991502: Scan Tool (MUT-II)
STEP 1. Check the ignition switch position.
Q: Does DTC 11 set with the ignition switch at "ON"
position?
YES : Go to Step 5.
NO : Go to Step 2.
AC003078 AB
CONNECTOR: C-60
COLUMN SWITCH
AC003079 AB
CONNECTOR
BLOCK (LH)
CONNECTOR: C-66
AC003082AB
CONNECTORS: C-73, C-78, C-82
C-82
C-73
C-78
JUNCTION BLOCK
(FRONT VIEW)
AC003080 AB
JUNCTION BLOCK
(REAR VIEW)
CONNECTOR: C-84
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-14
STEP 2. Check the column switch power supply circuit
(battery circuit) at the column switch connector C-60 by
backprobing.
(1)Do not disconnect the column switch connector C-60.
(2)Measure the voltage between terminal 1 and ground by
backprobing.
Q: Is the voltage approximately 12 volts (battery positive
voltage)?
YES : Go to Step 8.
NO : Go to Step 3.
STEP 3. Check the column switch connector C-60 for
damage.
Q: Is column switch connector C-60 in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. Confirm the DTC 12
is not displayed.
STEP 4. Check the harness wires between column switch
connector C-60 and battery.
NOTE: After checking joint connectors C-66, check the wires. If
intermediate connector C-66 is damaged, repair or replace it.
Refer to GROUP 00E, Harness Connector Inspection
Q: Are the harness wires between column switch
connector C-60 and battery in good condition?
YES : There is no action to be taken.
NO : Repair them. Confirm the DTC 12 is not displayed.
AC003087 AB
CONNECTOR C-60
(HARNESS SIDE)
AC003078 AB
CONNECTOR: C-60
COLUMN SWITCH
AC003078 AB
CONNECTOR: C-60
COLUMN SWITCH
AC003079 AB
CONNECTOR
BLOCK (LH)
CONNECTOR: C-66
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст