Mitsubishi Galant. Manual — part 415
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-127
STEP 2. Check the Park/Neutral position switch.
Check for continuity between terminals for each selector
position.
Q: Is the switch operating properly?
YES : Go to Step 3.
NO : Replace the Park/Neutral position switch. Refer to
GROUP 23B, Transaxle
.
ITEMS
TERMINAL CONNECTION
OF TESTER
SPECIFIED
CONDITION
P
3
−
8, 9
−
10
Less than 2 ohm.
R
7
−
8
N
4
−
8, 9
−
10
D
1
−
8
3
5
−
8
2
2
−
8
L
6
−
8
AC004672
DIPSTICK
PARK/NEUTRAL
POSITION (PNP)
SWITCH
AC
AC001846
P
R
N
D
3
2
L
AB
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-128
STEP 3. Check connectors B-39 at Park/Neutral position
switch, C-17 at intermediate connector and C-77 at
junction block for damage.
Q: Are the connectors in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
AC001844AI
CONNECTOR: B-39
DIPSTICK
AC004308AB
CONNECTOR: C-17
AC004307
CONNECTOR: C-77
JUNCTION BLOCK
(FRONT VIEW)
C-77
AC
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-129
STEP 4. Check harness for open circuit or short circuit to
ground between Park/Neutral position switch connector B-
39 terminal 8 and junction block connector C-77 terminal
12.
Q: Is the harness wire in good condition?
YES : Go to Step 5.
NO : Repair it.
STEP 5. Using scan tool MB991502, check data list item 61:
Park/Neutral Position Switch.
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting scan tool MB991502.
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Set scan tool MB991502 to data reading mode for item 61:
Park/Neutral Position Switch.
•
Move the selector lever to "P," "R," "N," "D," "3," "2," "L"
positions to confirm whether the MUT-II.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the switch operating properly?
YES : This malfunction is intermittent. Refer to GROUP 00,
How to Use Troubleshooting/Inspection Service
Points
−
How to Cope with Intermittent Malfunction
NO : Replace the PCM.
AC001844AI
CONNECTOR: B-39
DIPSTICK
AC004307
CONNECTOR: C-77
JUNCTION BLOCK
(FRONT VIEW)
C-77
AC
AC003081AC
MB991502
DATA LINK
CONNECTOR
AUTOMATIC TRANSAXLE DIAGNOSIS
TSB Revision
AUTOMATIC TRANSAXLE
23A-130
STEP 6. Check the Park/Neutral position switch.
Check for continuity between terminals for each selector
position.
Q: Is the switch operating properly?
YES : Go to Step 7.
NO : Replace the Park/Neutral position switch. Refer to
GROUP 23B, Transaxle
.
STEP 7. Check connector B-39 at the Park/Neutral position
switch for damage.
Q: Is the connector in good condition?
YES : Go to Step 8.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
.
ITEMS
TERMINAL CONNECTION
OF TESTER
SPECIFIED
CONDITION
P
3
−
8, 9
−
10
Less than 2 ohm.
R
7
−
8
N
4
−
8, 9
−
10
D
1
−
8
3
5
−
8
2
2
−
8
L
6
−
8
AC004672
DIPSTICK
PARK/NEUTRAL
POSITION (PNP)
SWITCH
AC
AC001846
P
R
N
D
3
2
L
AB
AC001844AI
CONNECTOR: B-39
DIPSTICK
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст