Mitsubishi Galant. Manual — part 362
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-18
STEP 3. Check the harness wire between auto-cruise
control-ECU connector C-52 and joint connector (2) C-56.
Q: Is any harness wire between auto-cruise control-ECU
connector C-52 and joint connector (2) C-56 damaged?
YES : Repair the harness wire and then check that
diagnostic trouble code 12 is not output.
NO : Check that diagnostic trouble code 12 is not output.
If diagnostic trouble code 12 is output, replace the
auto-cruise control-ECU. (Refer to
.)
Then check that diagnostic trouble code 12 is not
output.
AC004572AB
CONNECTOR: C-52
AC004577AB
CONNECTOR: C-56
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-19
DTC14 : Stoplight Switch System
AC004578AB
Stoplight Switch System Circuit
AC001449
CONNECTOR: A-01
RESERVE
TANK
AB
AC004579
CONNECTORS: C-03, C-05
AB
C-03
C-05
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-20
CIRCUIT OPERATION
This circuit supplies the power to the vacuum pump.
The battery positive voltage is supplied to the auto-
cruise control vacuum pump by turning on the
transistor at terminal number 16 of the auto-cruise
control-ECU.
The conditions for turning on the transistor at
terminal number 16 of the auto-cruise control-ECU
are as follows.
•
Ignition switch "ON"
•
Auto-cruise control main switch "ON"
•
Stoplight switch ON
DTC SET CONDITIONS
None of the drive signals from release valve, control
valve and motor of the auto-cruise vacuum pump are
input to the auto-cruise control-ECU.
TROUBLESHOOTING HINTS
The most likely causes for this code to be set are:
•
Malfunction of the stoplight switch
•
Malfunction of the auto-cruise vacuum pump
•
Damaged harness or connector.
•
Malfunction of the auto-cruise control-ECU
DIAGNOSIS
Required Special Tool:
•
MB991223: Harness Set
STEP 1. Check the output circuit voltage at stoplight
switch connector C-03 by backprobing.
(1) Do not disconnect stoplight switch connector C-03.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 3 and ground by
backprobing.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage approximately battery positive voltage?
YES : Go to Step 3.
NO : Go to Step 2.
AC004573AC
GLOVE BOX
CONNECTOR: C-12
AC004580AB
CONNECTOR: C-66
CONNECTOR
BLOCK(LH)
AC004572AB
CONNECTOR: C-52
1
3
4
2
ACX01910
C-03 CONNECTOR
HARNESS SIDE VIEW
AC
AUTO-CRUISE CONTROL
TSB Revision
ENGINE AND EMISSION CONTROL
17-21
STEP 2. Check stoplight switch connector C-03.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that diagnostic trouble code 14 is not
output.
NO : Go to Step 13.
STEP 3. Check the output circuit voltage at stoplight
switch connector C-03 by backprobing.
(1) Do not disconnect stoplight switch connector C-03.
(2) Turn the ignition switch to "ON" position and the auto-cruise
control main switch to "ON" position.
(3) Measure the voltage between terminal 4 and ground by
backprobing.
(4) Turn the ignition switch to "LOCK" (OFF) position.
Q: Is the voltage approximately battery positive voltage?
YES : Go to Step 6.
NO : Go to Step 4.
STEP 4. Check stoplight switch connector C-03.
Q: Is the connector damaged?
YES : Repair or replace connector.
Refer to GROUP 00E, Harness Connector Inspection
.
Then check that diagnostic trouble code 14 is not
output.
NO : Go to Step 5.
AC004581
CONNECTOR: C-03
AB
1
3
4
2
ACX01911AC
C-03 CONNECTOR
HARNESS SIDE VIEW
AC004581
CONNECTOR: C-03
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст