Mitsubishi Galant. Manual — part 626
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-57
CIRCUIT OPERATION
•
The ignition switch (IG1) circuit is the power
source for the engine coolant temperature gauge.
•
Resistance value, which the engine coolant
temperature gauge unit sends to the combination
meter, is dependent on temperature of the engine
coolant. This causes circuit current to fluctuate.
•
The engine coolant temperature gauge moves
the needle according to the circuit current.
TECHNICAL DESCRIPTION (COMMENT)
If the ignition switch (IG1) circuit is open, the gauge
needle will not move at all. If the ground circuit is
open, the gauge needle will move up to its extreme
position.
TROUBLESHOOTING
•
Malfunction of the engine coolant temperature gauge unit
•
Malfunction of the combination meter (printed-circuit board
or engine coolant temperature gauge assembly)
•
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tool:
MB991223: Harness Set
AC001750AC
ENGINE COOLANT
TEMPERATURE GAUGE UNIT
CONNECTOR: B-07
<2.4L ENGINE>
AC001751AC
ENGINE COOLANT
TEMPERATURE GAUGE UNIT
CONNECTOR: B-07
<3.0L ENGINE>
AC003089 AI
CONNECTOR: C-17
AC003089 AD
CONNECTOR: C-29
AC003082 AM
CONNECTORS: C-73, C-78
C-73
C-78
JUNCTION BLOCK
(FRONT VIEW)
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-58
STEP 1. Check the speedometer operation.
Q: Does the speedometer work normally?
YES : Go to Step 2.
NO : Refer to Inspection Procedure 1
.
STEP 2. Check the engine coolant temperature sensor
signal circuit at the engine coolant temperature sensor
connector B-07 by backprobing.
(1) Do not disconnect the engine coolant temperature sensor
connector B-07.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 1 and ground by
backprobing.
Q: Is the voltage approximately 9 volts or more?
YES : Go to Step 5.
NO : Go to Step 3.
AC003722AB
CONNECTOR: B-07
(HARNESS SIDE)
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-59
STEP 3. Check the engine coolant temperature sensor
connector B-07 and combination meter connector C-29 for
damage.
Q: Are engine coolant temperature sensor connector B-07
and combination meter connector C-29 in good
condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The engine coolant
temperature gauge should work normally.
AC001750AC
ENGINE COOLANT
TEMPERATURE GAUGE UNIT
CONNECTOR: B-07
<2.4L ENGINE>
AC001751AC
ENGINE COOLANT
TEMPERATURE GAUGE UNIT
CONNECTOR: B-07
<3.0L ENGINE>
AC003089 AD
CONNECTOR: C-29
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-60
STEP 4. Check the harness wires between engine coolant
temperature sensor connector B-07 and combination
meter connector C-29.
NOTE: After checking intermediate connector C-17, check the
wire. If intermediate connector C-17 is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector
Inspection
Q: Are the harness wires between engine coolant
temperature sensor connector B-07 and combination
meter connector C-29 in good condition?
YES : Repair or replace the combination meter (printed-
circuit board or engine coolant temperature gauge
assembly). The engine coolant temperature gauge
should work normally.
NO : Repair them. The engine coolant temperature gauge
should work normally.
AC001750AC
ENGINE COOLANT
TEMPERATURE GAUGE UNIT
CONNECTOR: B-07
<2.4L ENGINE>
AC001751AC
ENGINE COOLANT
TEMPERATURE GAUGE UNIT
CONNECTOR: B-07
<3.0L ENGINE>
AC003089 AD
CONNECTOR: C-29
AC003089 AI
CONNECTOR: C-17
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст