Mitsubishi Galant. Manual — part 625
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-53
STEP 2. Check the fuel pump module signal circuit at the
fuel pump module connector D-14 by backprobing.
(1) Do not disconnect the fuel pump module connector D-14.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 2 and ground by
backprobing.
Q: Is the voltage approximately 5 volts or more?
YES : Go to Step 5.
NO : Go to Step 3.
STEP 3. Check the fuel pump module connector D-14 and
combination meter connector C-29 for damage.
Q: Are fuel pump module connector D-14 and combination
meter connector C-29 in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. The fuel gauge should
work normally.
AC003720AB
CONNECTOR: D-14
(HARNESS SIDE)
AC003089 AD
CONNECTOR: C-29
AC001749AC
FUEL PUMP
MODULE
CONNECTOR: D-14
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-54
STEP 4. Check the harness wires between fuel pump
module connector D-14 and combination meter connector
C-29.
NOTE: After checking intermediate connector C-71, check the
wire. If intermediate connector C-71 is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector
Inspection
Q: Are the harness wires between fuel pump module
connector D-14 and combination meter connector C-29
in good condition?
YES : Repair or replace the combination meter (printed-
circuit board or fuel gauge assembly). The fuel gauge
should work normally.
NO : Repair them. The fuel gauge should work normally.
STEP 5. Check the fuel pump module ground circuit at the
fuel pump module connector D-14 by backprobing.
(1) Do not disconnect the fuel gauge unit connector D-14.
(2) Measure the resistance between terminal 1 and ground by
backprobing.
Q: Is the resistance less than 2 ohms?
YES : Go to Step 8.
NO : Go to Step 6.
AC003089 AD
CONNECTOR: C-29
AC001749AC
FUEL PUMP
MODULE
CONNECTOR: D-14
AC003415 AC
CONNECTOR: C-71
CONNECTOR
BLOCK (RH)
AC003721AB
CONNECTOR: D-14
(HARNESS SIDE)
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-55
STEP 6. Check the fuel pump module connector D-14 for
damage.
Q: Is fuel gauge unit connector D-14 in good condition?
YES : Go to Step 7.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. The fuel gauge should
work normally.
STEP 7. Check the harness wire between fuel pump
module connector D-14 and ground.
Q: Is the harness wire between fuel pump module
connector D-14 and ground in good condition?
YES : There is no action to be taken.
NO : Repair them. The fuel gauge should work normally.
STEP 8. Check the fuel gauge unit.
(1) Remove the fuel pump module from the fuel tank. (Refer to
GROUP 13C, Fuel Tank
(2) Check resistance value between terminals 2 and 1 is at
standard value when the fuel gauge unit float is at point "F"
(highest) and point "E" (lowest).
(3) Check that the resistance value changes smoothly when
the float moves slowly between point "F" (highest) and "E"
(lowest).
Q: Is the resistance 3
−−−−
5 ohms (at point "F") and 110
−−−−
112
ohms (at point "E")?
YES : Repair or replace the combination meter (printed-
circuit board or fuel gauge assembly). The fuel gauge
should work normally.
NO : Replace the fuel gauge unit. The fuel gauge should
work normally.
AC001749AC
FUEL PUMP
MODULE
CONNECTOR: D-14
AC001749AC
FUEL PUMP
MODULE
CONNECTOR: D-14
AC001282
POINT "E"
FLOAT
FUEL PUMP
MODULE
AC
POINT "F"
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-56
Inspection Procedure 4: Engine coolant temperature gauge does not work.
AC003968
Engine Coolant Temperature Gauge Circuit
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст