Mitsubishi Galant. Manual — part 618
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-25
6. Select "key ID registr,"press "YES".
If DTC 11 exists,"Can't execute" will be displayed.Check for
DTC 11(Refer to
.)
7. Input the password. Use the "UP" and "DOWN" keys to
change the current password digit to a value between 0 and
9. Use the "LEFT" and "RIGHT" keys to move to a different
password digit. Press the "YES" key to accept the
password.
NOTE: Four separate digits must be input to make up the
password.
If an incorrect password is input five times in a row, this screen
is displayed and the Immobilizer-ECU switches to unauthorized
operation, start-prevention mode.
8. Press the "YES" key to start key ID registration.
9. This will be displayed when the key ID registration is
successful. If an error occurs during key ID registration, the
message "Can't execute" will be displayed. If the key has
already been registered, "Key ID has been registered" will
be displayed.
AC000518
AB
ACX01558
ACX01626AB
ACX01561AC
ACX01562AB
TSB Revision
CHASSIS ELECTRICAL
IGNITION SWITCH
54A-26
10.The number of keys currently registered will be displayed.
To register an additional key, replace the ignition key with
the next key to be registered within five seconds and then
press the "YES" key. Key ID registration screen will be
displayed, then register another key.
NOTE: A maximum of eight different keys can be registered.
If key ID registration is complete, press the "NO" key.
11.This completes the registration operation. Turn the ignition
switch "LOCK" (OFF) and leave it off for approximately ten
seconds.
12.Check that the engine can be started with each of the
ignition keys.
13.Check that the immobilizer system DTC and MFI system
DTC did not set.
14.Turn the ignition switch to "LOCK" (OFF) position.
15.Disconnect scan tool MB991502.
IGNITION SWITCH REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
M1543002100100
ACX01563 AB
AC002879
1
2
3
4
5
6
7
8
9
10
11
AB
1.
ETACS-ECU (GROUP 42, KEYLESS
ENTRY SYSTEM
.)
>>A<<
2.
IMMOBILIZER-ECU
IGNITION SWITCH REMOVAL
STEPS
3.
HOOD LOCK RELEASE HANDLE
4.
DRIVER'S UNDERCOVER (REFER
TO GROUP 52A, INSTRUMENT
PANEL
.)
5.
COLUMN COVER, UPPER
6.
COLUMN COVER, LOWER
7.
KEY RING ANTENNA
8.
BULB
9.
KEY REMINDER SWITCH
<<A>>
10. STEERING LOCK CYLINDER
11. IGNITION SWITCH
IGNITION SWITCH REMOVAL
STEPS (Continued)
IGNITION SWITCH
TSB Revision
CHASSIS ELECTRICAL
54A-27
REMOVAL SERVICE POINT
<<A>> STEERING LOCK CYLINDER REMOVAL
1. Insert the key in the steering lock cylinder and turn it to the
"ACC" position.
2. Using a small Phillips head screwdriver, pull the steering
lock cylinder toward you.
INSTALLATION SERVICE POINT
>>A<< IMMOBILIZER-ECU INSTALLATION
If the immobilizer-ECU is replaced, peel off the immobilizer
serial number sticker from shown position. Then attach a new
immobilizer-ECU identification sticker.
IGNITION SWITCH INSPECTION
M1543002200099
IGNITION SWITCH CONTINUITY CHECK
Disconnect ignition switch connector C-58 without removing
the ignition switch and steering lock cylinder. Then check the
continuity.
AC002880 AB
SMALL
PHILLIPS HEAD
SCREWDRIVER
AC002881AB
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONNECTION
"LOCK"(OFF)
-
-
"ACC"
1-6
Continuity
"ON"
1-2-4-6
Continuity
"START"
1-2-3-5
Continuity
AC002882AB
CONNECTOR: C-58
COLUMN SWITCH
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-28
KEY REMINDER SWITCH CHECK
Disconnect key reminder switch connector C-59 without
removing the key reminder switch and steering lock cylinder.
Then check the continuity.
Ignition key ring antenna check
Check the continuity between terminal 3 and terminal 7.
Standard value: 2 ohms or less
CO M B IN ATIO N M ETERS A SSEM BLY AND VEH IC LE SPEED
SENSO R
INTRODUCTION TO COMBINATION METER DIAGNOSIS
M1543009900312
All vehicles are equipped with an electrical
speedometer and tachometer. If the speedometer or
tachometer does not function, there may be trouble
in the electrical system.
COMBINATION METER DIAGNOSTIC TROUBLESHOOTING STRATEGY
M1543006900186
Use these steps to plan your diagnostic strategy. If
you follow them carefully, you will be sure that you
have exhausted most of the possible ways to find a
combination meter fault.
1. Gather information from the customer.
2. Verify that the condition described by the
customer exists.
3. Find the malfunction by following the symptom
chart.
4. Verify the malfunction is eliminated.
SYMPTOM CHART
M1543007200243
STATUS OF
IGNITION KEY
TESTER
CONNECTION
SPECIFIED
CONNECTION
Removed
1-2(Illumination
light)
4-6(Switch)
Continuity
Inserted
1-2(Illumination
light)
Continuity
AC002876
CONNECTOR: C-59
COLUMN SWITCH
AB
SYMPTOMS
INSPECTION
PROCEDURE
REFERENCE PAGE
Speedometer does not work.
1
Tachometer does not work.
2
Fuel gauge does not work.
3
Engine coolant temperature gauge does not work.
4
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст