Mitsubishi Galant. Manual — part 619
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-29
SYMPTOM PROCEDURES
Inspection Procedure 1: Speedometer does not work.
AC003970
Speedometer Circuit
AB
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-30
CIRCUIT OPERATION
•
The ignition switch (IG1) circuit is the power
source for the speedometer and vehicle speed
sensor.
•
The vehicle speed sensor is installed on the
transaxle. Four pulses are generated with one
turn of the vehicle speed sensor shaft. These
pulse signals are sent into the speedometer. The
speedometer calculates the pulse signals, and
operates the indicator. At the same time, the
travel distance is calculated.
AC003686
CONNECTOR: B-35
<2.4L ENGINE>
AB
AC003687
CONNECTOR: B-35
<3.0L ENGINE>
AB
AC003089
C-17
C-31
CONNECTORS: C-17, C-31
AN
AC003089
C-56
CONNECTORS: C-29, C-30, C-56
AO
C-30
C-29
AC003685
CONNECTOR: C-41
AC
PCM
AC003688
AC003688
CONNECTOR: C-52
AB
CENTER REINFORCEMENT
AUTO-CRUISE CONTROL-ECU
AC003082AV
CONNECTORS: C-73, C-74, C-78
C-73
C-78
JUNCTION BLOCK
(FRONT VIEW)
C-74
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-31
TECHNICAL DESCRIPTION (COMMENT)
The cause may be a faulty vehicle speed sensor
circuit system or a faulty speedometer. Vehicle
speed sensor is also used by the powertrain control
module (PCM), auto-cruise control-ECU.
TROUBLESHOOTING HINTS
•
Malfunction of the vehicle speed sensor
•
Malfunction of the combination meter (printed-
circuit board or speedometer and tachometer)
•
Malfunction of the PCM
•
Malfunction of the auto-cruise control-ECU
•
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tools:
•
MB991223: Harness Set
•
MB991502: Scan Tool (MUT-II)
CAUTION
To prevent damage to scan tool always turn the ignition
switch to "LOCK" (OFF) position before connecting or
disconnecting scan tool.
STEP 1. Check the vehicle speed sensor
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Read the MFI system diagnostic trouble code.
Q: Is MFI system DTC P0500 output?
YES : Go to Step 12.
NO : Go to Step 2.
STEP 2. Check the odometer and trip odometer operation.
Q: Do the odometer and trip odometer work correctly?
YES : Go to Step 9.
NO : Go to Step 3.
STEP 3. Check the combination meter power supply circuit
at the combination meter connector C-29.
(1) Disconnect the combination meter connector C-29.
(2) Turn the ignition switch to "ON" position.
(3) Measure the voltage between terminal 29 and ground.
Q: Is the voltage 12 volts (battery positive voltage) between
terminal 29 and ground?
YES : Go to Step 6.
NO : Go to Step 4.
AC002883
16PIN
MB991502
AB
AC002884AB
CONNECTOR: C-29
(HARNESS SIDE)
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-32
STEP 4. Check the combination meter connector C-29 for
damage.
Q: Is combination meter connector C-29 in good
condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The speedometer
should work normally.
STEP 5. Check the harness wires between combination
meter connector C-29 and ignition switch (IG1).
NOTE: After checking junction block connectors C-73 and C-
78, check the wires. If junction block connectors C-73 and C-78
are damaged, repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
.
Q: Is the harness wires between combination meter
connector C-29 and ignition switch (IG1) in good
condition?
YES : There is no action to be taken.
NO : Repair them. The speedometer should work normally.
STEP 6. Check the combination meter (speedometer)
ground circuit at the combination meter connector C-29.
(1) Disconnect the combination meter connector C-29.
(2) Measure the resistance between terminal 30 and ground.
Q: Is the resistance value less than 2 ohms?
YES : Repair or repair the combination meter (printed-circuit
board or speedometer and tachometer). The
speedometer should work normally.
NO : Go to Step 7.
AC003089 AD
CONNECTOR: C-29
AC003089 AD
CONNECTOR: C-29
AC003082 AM
CONNECTORS: C-73, C-78
C-73
C-78
JUNCTION BLOCK
(FRONT VIEW)
AC002885
(HARNESS SIDE)
CONNECTOR: C-29
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст