Mitsubishi Galant. Manual — part 712
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-243
STEP 13. Check the harness wires between power window
sub switch connector E-05 and ETACS-ECU connector C-
81.
NOTE: After checking intermediate connector C-72, check the
wires. If intermediate connector C-72 is damaged, repair or
replace it. Refer to GROUP 00E, Harness Connector
Inspection
.
Q: Are the harness wires between power window sub
switch connector E-05 and ETACS-ECU connector C-81
in good condition?
YES : Replace the ETACS-ECU. The door lock switch input
signal should be able to be checked and the central
door locking system should work normally.
NO : Repair them. The door lock switch input signal should
be able to be checked and the central door locking
system should work normally.
AC003082 AJ
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-81
AC003086 AN
DOOR
CONNECTOR: E-05
AC003415 AD
CONNECTOR: C-72
CONNECTOR
BLOCK (RH)
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-244
Inspection Procedure N-11: The Hood switch signal is not sent to the ETACS-ECU.
AC004245
Hood Switch Input Circuit
AC003129 AG
CONNECTOR: A-25
AC003079 AB
CONNECTOR
BLOCK (LH)
CONNECTOR: C-66
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-245
CIRCUIT OPERATION
The ETACS-ECU operates the hood switch
according to the input signal from the theft-alarm
system switch.
TECHNICAL DESCRIPTION (COMMENT)
The theft-alarm system will not work normally if the
hood switch input signal is an error.
TROUBLESHOOTING HINTS
•
Malfunction of the hood switch
•
Malfunction of the ETACS-ECU
•
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tools:
•
MB991223: Test Harness Set
•
MB991502: Scan Tool (MUT-II)
•
MB991529: Diagnostic Trouble Code Check Harness
STEP 1. Check the hood switch.
Q: Is the hood switch in good condition?
YES : Go to Step 2.
NO : Repair it. The hood switch input signal should be able
to be checked and the theft-alarm should work
normally.
AC003082 AJ
JUNCTION BLOCK
(FRONT VIEW)
CONNECTOR: C-81
SWITCH
POSITION
TESTER
CONNECTION
SPECIFIED
CONDITION
Released
−
No continuity
Pressed
1
−
2
Continuity
AC003413
SWS DIAGNOSIS
TSB Revision
SIMPLIFIED WIRING SYSTEM (SWS)
54B-246
STEP 2. Check the hood switch ground circuit at the hood
switch connector A-25.
(1)Disconnect the hood switch connector A-25 and measure at
the harness side.
(2)Measure the resistance between terminal 1 and ground.
Q: Is the resistance less than 2 ohm?
YES : Go to Step 5.
NO : Go to Step 3.
STEP 3. Check hood switch connector A-25 for damage.
Q: Is hood switch connector A-25 in good condition?
YES : Go to Step 4.
NO : Repair or replace it. Refer to GROUP 00E, Harness
. The hood switch input
signal should be able to be checked and the theft-
alarm system should work normally.
STEP 4. Check the harness wires between hood switch
connector A-25 and ground.
Q: Are the harness wires between hood switch connector
A-25 and ground in good condition?
YES : There is no action to be taken.
NO : Repair them. The hood switch input signal should be
able to be checked and the theft-alarm system should
work normally.
AC003418 AC
CONNECTOR A-25
(HARNESS SIDE)
AC003129 AG
CONNECTOR: A-25
AC003129 AG
CONNECTOR: A-25
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст