Mitsubishi Galant. Manual — part 623
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-45
Inspection Procedure 2: Tachometer does not work.
AC003971
Tachometer Circuit
AB
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-46
CIRCUIT OPERATION
•
The tachometer power is supplied from the
ignition switch (IG) circuit.
•
For vehicles with 2.4L engine, the tachometer
detects the ignition signal by the engine control
module via the ignition failure sensor.
•
For vehicles with 3.0L engine, the tachometer
detects the ignition signal control via the
distributor assembly.
TECHNICAL DESCRIPTION (COMMENT)
The ignition signal may not be sent from the engine,
or there may be a malfunction in the power supply or
ground circuit.
TROUBLESHOOTING HINTS
•
Malfunction of the combination meter (printed
circuit board or speedometer and tachometer)
•
Damaged harness wires or connectors
DIAGNOSIS
Required Special Tools:
•
MB991223: Harness Set
•
MB991502: Scan Tool (MUT-II)
AC003693AB
CONNECTOR: B-01
<2.4L ENGINE>
AC003694AB
CONNECTOR: B-27
<3.0L ENGINE>
AC003089
CONNECTOR: C-16
AS
AC003089 AI
CONNECTOR: C-17
AC003089
CONNECTORS: C-29, C-30
AR
C-30
C-29
AC003082 AM
CONNECTORS: C-73, C-78
C-73
C-78
JUNCTION BLOCK
(FRONT VIEW)
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-47
CAUTION
To prevent damage to scan tool MB991502, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting scan tool.
STEP 1. Check the vehicle speed sensor
(1) Connect scan tool MB991502 to the data link connector.
(2) Turn the ignition switch to "ON" position.
(3) Read the MFI system diagnostic trouble code.
Q: Is MFI system DTC P0300 output?
YES : Refer to GROUP 13A,Diagnosis
and
GROUP 13B, Diagnosis
NO : Go to Step 2.
STEP 2. Check the speedometer operation.
Q: Does the speedometer work normally?
YES : Refer to Inspection Procedure 1
.
NO : Go to Step 3.
STEP 3. Check the combination meter (tachometer)
ground circuit at the combination meter connector C-30.
(1) Disconnect the combination meter connector C-30.
(2) Measure the resistance between terminal 15 and ground.
Q: Is the resistance less than 2 ohms?
YES : Go to Step 5.
NO : Go to Step 4.
AC002883
16PIN
MB991502
AB
AC003719AB
CONNECTOR: C-30
(HARNESS SIDE)
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-48
STEP 4. Check the ignition failure sensor connector B-01
<2.4L engine>, distributor assembly connector B-27 <3.0L
engine>, automatic compressor controller connector C-16
<3.0L engine> and combination meter connector C-30 for
damage.
Q: Is the ignition failure sensor connector B-01 <2.4L
engine>, distributor assembly connector B-27 <3.0L
engine>, automatic compressor controller connector C-
16 <3.0L engine> and combination meter connector C-
30 for damage in good condition?
YES : Go to Step 5.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The tachometer
should work normally.
AC003693AB
CONNECTOR: B-01
<2.4L ENGINE>
AC003694AB
CONNECTOR: B-27
<3.0L ENGINE>
AC003089
CONNECTOR: C-16
AS
AC003089 AH
CONNECTOR: C-30
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст