Mitsubishi Galant. Manual — part 621
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-37
STEP 14. Check the harness wires between vehicle speed
sensor connector B-35 and ignition switch (IG1).
NOTE: After checking junction block connectors C-73 and C-
74, intermediate connector C-17, check the wires. If junction
block connectors C-73 and C-74, intermediate connector C-17
are damaged, repair or replace them. Refer to GROUP 00E,
Harness Connector Inspection
Q: Are the harness wires between vehicle speed sensor
connector B-35 and ignition switch (IG1) in good
condition?
YES : There is no action to be taken.
NO : Repair them. The speedometer should work normally.
AC003686
CONNECTOR: B-35
<2.4L ENGINE>
AB
AC003687
CONNECTOR: B-35
<3.0L ENGINE>
AB
AC003089 AI
CONNECTOR: C-17
AC003082AW
CONNECTORS: C-73, C-74
C-73
JUNCTION BLOCK
(FRONT VIEW)
C-74
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-38
STEP 15. Check the vehicle speed sensor ground circuit at
the vehicle speed sensor connector B-35.
(1) Disconnect the vehicle speed sensor connector B-35.
(2) Measure the resistance between terminal 2 and ground.
Q: Is the resistance less than 2 ohms?
YES : Go to Step 18.
NO : Go to Step 16.
STEP 16. Check the vehicle speed sensor connector B-35
for damage.
Q: Is vehicle speed connector B-35 in good condition?
YES : Go to Step 17.
NO : Repair or replace it. Refer to GROUP 00E, Harness
Connector Inspection
. The speedometer
should work normally.
AC002751AB
CONNECTOR: B-35
(HARNESS SIDE)
AC003686
CONNECTOR: B-35
<2.4L ENGINE>
AB
AC003687
CONNECTOR: B-35
<3.0L ENGINE>
AB
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
TSB Revision
CHASSIS ELECTRICAL
54A-39
STEP 17. Check the harness wire between vehicle speed
sensor connector B-35 and ground.
Q: Is the harness wire between vehicle speed sensor
connector B-35 and ground in good condition?
YES : There is no action to be taken.
NO : Repair it. The speedometer should work normally.
STEP 18. Check the vehicle speed sensor signal circuit at
the vehicle speed sensor connector B-35.
(1) Disconnect the vehicle speed sensor connector B-35.
(2) Turn the ignition switch to "ON"
(3) Measure the voltage between terminal 3 and ground.
Q: Is the voltage approximately 9 volts or more?
More than approximately 9 volts : Replace the vehicle
speed sensor. The speedometer should work
normally.
Approximately 9 volts : Go to Step 19 .
AC003686
CONNECTOR: B-35
<2.4L ENGINE>
AB
AC003687
CONNECTOR: B-35
<3.0L ENGINE>
AB
AC002749AB
CONNECTOR: B-35
(HARNESS SIDE)
TSB Revision
CHASSIS ELECTRICAL
COMBINATION METERS ASSEMBLY AND VEHICLE SPEED SENSOR
54A-40
STEP 19. Check the vehicle speed sensor connector B-35,
radio and tape player connector C-31, auto-cruise control-
ECU connector C-52 <vehicles with auto-cruise control>,
PCM connector C-41 and combination meter connector C-
30.
AC003686
CONNECTOR: B-35
<2.4L ENGINE>
AB
AC003687
CONNECTOR: B-35
<3.0L ENGINE>
AB
AC003089
C-31
CONNECTORS: C-30, C-31
AQ
C-30
AC003685
CONNECTOR: C-41
AC
PCM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст